+ Reply to Thread
Results 1 to 13 of 13

Thread: Odd kegger mod

  1. #1
    Junior Member

    Status
    Offline
    Join Date
    Mar 2019
    Location
    Wrightstown NJ
    Posts
    27

    Default Odd kegger mod

    So I’ve been doing some searching on kegger mod and get a50/50 yays and nays. Well I found this. I had this in my mind but didn’t know if it was even possible. Wide open like a Hemi or an LS. What do you guys think?
    9EB085CB-B4B8-48A5-8914-5B29760E1D77.jpg

  2. #2



    Senior Member

    Status
    Offline
    Join Date
    Feb 2008
    Location
    Corrales, New Mexico
    Posts
    17,966

    Default

    Don't bother.
    11.27 @ 118.23
    2017 NM Mopar Challenge Series Champion

  3. #3




    slammedR/T's Avatar
    "Bleach Master"

    Status
    Offline
    Join Date
    Jan 2008
    Location
    Jacksonville, FL.
    Posts
    3,910

    Default

    First, you haven't looked inside a hemi or LS intake.
    Second, you just lost all low end torque
    Third, the "kegger" mods have been all dyno tested numerous times and they didn't make any more power and a couple actually lost a few horsepower along with torque.
    This signature has been deleted thanks to photobucket!

  4. #4



    Senior Member

    Status
    Offline
    Join Date
    Feb 2008
    Location
    Corrales, New Mexico
    Posts
    17,966

    Default

    Facts ^^^
    11.27 @ 118.23
    2017 NM Mopar Challenge Series Champion

  5. #5


    99dart's Avatar
    Senior Member

    Status
    Offline
    Join Date
    Feb 2008
    Location
    Washington...the hot side!
    Posts
    3,886

    Default

    I ran the "Kammer & Kammer" modified intake many moons ago. To me it felt like it had great off the line TQ. I was producing great 60' times for a basically stock motor. Just pph headers, no cat, one of my home ported 50mm TB's and 28" ET streets. IIRC, my 60's were 1.92ish. Of course I was in Bremerton where we had great air too! ;P Dave
    99 DA CC R/T
    13.97@100 w/modded kegger & ported TB
    12.96 @103
    10:8-1 .30 over forged bottom end
    R/T ported heads
    Detroit locker 4:56 gears
    Built 46RE MSaine 3500 stall Ultra Billet
    http://imgur.com/a/lOVuZ

  6. #6
    niebs's Avatar
    Senior Member

    Status
    Offline
    Join Date
    Jun 2015
    Location
    North DE
    Posts
    1,761

    Default

    So remove the runners completely? Bet she'll scream up top.

    Thanks for the pic tho cause im about to cut mine open to weld in a 4150 plate.

  7. #7




    slammedR/T's Avatar
    "Bleach Master"

    Status
    Offline
    Join Date
    Jan 2008
    Location
    Jacksonville, FL.
    Posts
    3,910

    Default

    Actual dyno numbers > butt dyno....
    This signature has been deleted thanks to photobucket!

  8. #8


    99dart's Avatar
    Senior Member

    Status
    Offline
    Join Date
    Feb 2008
    Location
    Washington...the hot side!
    Posts
    3,886

    Default

    Quote Originally Posted by slammedR/T View Post
    Actual dyno numbers > butt dyno....
    Butt dyno and track numbers. My signature 13.97 was with that combo and a pair of Danno's 26" ET streets.
    99 DA CC R/T
    13.97@100 w/modded kegger & ported TB
    12.96 @103
    10:8-1 .30 over forged bottom end
    R/T ported heads
    Detroit locker 4:56 gears
    Built 46RE MSaine 3500 stall Ultra Billet
    http://imgur.com/a/lOVuZ

  9. #9




    slammedR/T's Avatar
    "Bleach Master"

    Status
    Offline
    Join Date
    Jan 2008
    Location
    Jacksonville, FL.
    Posts
    3,910

    Default

    Quote Originally Posted by 99dart View Post
    Butt dyno and track numbers. My signature 13.97 was with that combo and a pair of Danno's 26" ET streets.
    Don't worry, that "kegger mod" did nothing, but whatever you need to tell yourself
    This signature has been deleted thanks to photobucket!

  10. #10

    Default

    heard a rumor Chad went 10.33 with nothing but a ported kegger and a hot air intake
    Be yourself, everyone else is already taken
    11.1 @ 120

  11. #11
    Junior Member

    Status
    Offline
    Join Date
    Mar 2019
    Location
    Wrightstown NJ
    Posts
    27

    Default

    Haha well thank you guys for all the great feedback. I can assume any time spent on it is just a waste. Probably pick up an extra just to mill the top off to figure out a roots blower

  12. #12
    Junior Member

    Status
    Offline
    Join Date
    Mar 2019
    Location
    Wrightstown NJ
    Posts
    27

    Default

    Quote Originally Posted by JamesEcker View Post
    heard a rumor Chad went 10.33 with nothing but a ported kegger and a hot air intake

    Lol wow can’t even get that kind of mod response from a Cts-v

  13. #13




    slammedR/T's Avatar
    "Bleach Master"

    Status
    Offline
    Join Date
    Jan 2008
    Location
    Jacksonville, FL.
    Posts
    3,910

    Default

    Quote Originally Posted by Mattp232 View Post
    Haha well thank you guys for all the great feedback. I can assume any time spent on it is just a waste. Probably pick up an extra just to mill the top off to figure out a roots blower
    Look into the "mod man" intake manifold from Indy Cylinder heads.
    This signature has been deleted thanks to photobucket!

+ Reply to Thread

Posting Permissions

  • You may post new threads
  • You may post replies
  • You may not post attachments
  • You may not edit your posts
  •