Feels good, Don't it!
Feels good, Don't it!
99 DA CC R/T
13.97@100 w/modded kegger & ported TB
12.96 @103
10:8-1 .30 over forged bottom end
R/T ported heads
Detroit locker 4:56 gears
Built 46RE MSaine 3500 stall Ultra Billet
http://imgur.com/a/lOVuZ
Went to the first car meet cruise in we have every Thursday evening when the weather is nice.
MTU Car Meet by Michael Wigg, on Flickr
Last edited by Wiggsy72; 08-08-2017 at 02:43 PM.
Whiplash Engine & Machine, FRP Tuned
Instagram moderator for dakota_rt_club
Running Ryan's base tune still and the engine runs excellent, it's hard to believe it runs so well and only about to get better with some fine tuning. I'll be doing some data logging when I get back in about two weeks. I'll be installing the SS JBA replacement "Y" pipe with two new NTK O2 sensors and the additional bung for the wideband sensor.
I'm approaching 1000kms so far on the rebuild and I got on it a bit once it was up to temp and yeah she's got some f'n power. Also sounds wicked with some more pronounced pop and bang than it did before, it's that good performance engine sound you want to hear.
Added a 1" aluminum spacer to the K&N air filter. Added Moroso plug wire stand offs and made up a new rubber flap for the rad as the old one kinda fell apart.
missing pics.....
Last edited by Wiggsy72; 08-08-2017 at 02:48 PM.
Whiplash Engine & Machine, FRP Tuned
Instagram moderator for dakota_rt_club
I also have the jba ss y- pipe and i think it really sucks. from day one i have fitment problems . it is to close to the transmission pan and the fitting that goes to the cat also sucks . the fitting on both my cats the oem and the direct replacement magnaflow give problems with the jba y pipe . i also have fitment problems with my gibson ss ceramic headers with the y pipe but you have jba headers so it might fit good on your headers . the jba is not a direct replacement pipe like they say it is . BTW very nice truck
Last edited by Wiggsy72; 06-14-2017 at 12:30 AM. Reason: Big fingers tiny keyboard on phone
Whiplash Engine & Machine, FRP Tuned
Instagram moderator for dakota_rt_club
The JBA 2945SY is not the correct fit for the Dakota 5.9 R/T, its missing the left and right Bank O2 sensor bungs and only single out to the Cat. Mine has two outs to the Cat (2 in and single out cat) which also makes it easy to go true dual eventually.
Untitled by Michael Wigg, on Flickr
Untitled by Michael Wigg, on Flickr
Untitled by Michael Wigg, on Flickr
Untitled by Michael Wigg, on Flickr
Untitled by Michael Wigg, on Flickr
Untitled by Michael Wigg, on Flickr
Cut off 2.5" of existing pipe to the Cat for the fit length to be spot on.
Untitled by Michael Wigg, on Flickr
IMG_9061 by Michael Wigg, on Flickr
Last edited by Wiggsy72; 08-08-2017 at 03:17 PM.
Whiplash Engine & Machine, FRP Tuned
Instagram moderator for dakota_rt_club
Get rid of those crimp clamps and get these instead;
https://www.summitracing.com/ga/part...50-1/overview/
This signature has been deleted thanks to photobucket!
Yes, I like those and my plan is to install them soon. I like them because they don't deform the pipe, apply even pressure all around and basically look much nicer. I think they come with most Flowmaster kits as well.
Whiplash Engine & Machine, FRP Tuned
Instagram moderator for dakota_rt_club
Your JBA y pipe design look much nicer then mine i see in the pictures that you have enough clearance by the transmission pan . this is how it should look . thanks for the pictures it really helps me out i will look again and try to fix mine . the problem is that the pipe comes against my transmission pan. if i would like to change transmission fluid i need to remove the y pipe other wise i cannot remove my transmission bolts. Thanks for the help and the pictures
Started configuring data logging today and did a test run. I'll have to add two more PID's for the fuel trim measurements by the looks of it. Try again tomorrow.
Whiplash Engine & Machine, FRP Tuned
Instagram moderator for dakota_rt_club
What's the screen you are running under the dash? Btw looks sweet !
Whiplash Engine & Machine, FRP Tuned
Instagram moderator for dakota_rt_club
Need some hard to find parts? https://www.moparpartsoverstock.com
Whiplash Engine & Machine, FRP Tuned
Instagram moderator for dakota_rt_club
Well I got my first data log out to Ryan last week. Within about 10 minutes he got a hold of me to confirm a couple things for the wide band sensor and guage. Twenty minutes later I had a new tune to load that truely made a difference.
Today I managed to do a WOT run but I didn't capture it which was to bad because it was a great solid pedal into the carpet run blowing the doors off some dude in a BMW. Next attempt was short and sweet and I hope it was enough for Ryan. I can always do it again
Whiplash Engine & Machine, FRP Tuned
Instagram moderator for dakota_rt_club
Got my TorcTite exhaust clamps from Summit today. Summit part number SUM-69220-1. I'll get them on this weekend with some updated photos.
I've deleted my account on Photobucket. I will edit and repost the photos previously posted but now held for ransom but that will take some time. Should be a good winter project.
Whiplash Engine & Machine, FRP Tuned
Instagram moderator for dakota_rt_club
Here's a video clip, nothing spectacular as I'm only backing up into the carport. I was just after some audio of the exhaust.
https://youtu.be/ph64HinM8po
Whiplash Engine & Machine, FRP Tuned
Instagram moderator for dakota_rt_club
Sounds good!
'03 Stampede Graphite Metallic Dakota R/T CC
FRP tune, M1 2bbl, HiPoTek 52mm TB, K&N 14" Filter, Headers, Flowmaster duals
Updated all the lost photos in this post no thanks to Photobucket.
Here is the updated exhaust clamps on the JBA "Y" pipe.
Untitled by Michael Wigg, on Flickr
Untitled by Michael Wigg, on Flickr
Untitled by Michael Wigg, on Flickr
Untitled by Michael Wigg, on Flickr
Whiplash Engine & Machine, FRP Tuned
Instagram moderator for dakota_rt_club
Makes my 3" spintech look huge.
1999 R/C Solar yellow
That looks very nice damn. how much hp will the 210xp cam add normally to a magnum 5.9 engine with eq heads just to get an idea for my top end build .did you already dyno your R/T? how much hp do you think your truck is making now .