1995 Dakota Club Cab, 408, 5spd, 8 3/4 rear end
also something to add, edelbrock 8018 linkage stud will work on the bottom most hole of the accel and thread right in, will be used on mine for an auxiliary return spring, the upper two predrilled holes that are close together at the top of the linkage are 10/32nd fine thread, the holes are too close together to put two screws in them though idk what accel was even thinking with those holes
1995 Dakota Club Cab, 408, 5spd, 8 3/4 rear end
410, 10.3 comp pistons, P&P Eddies, 254 cam, 30lb injectors, sct tuner, 3800 viper stall, 4:56 yukon gears, hotchkis tvs, m1 4brrl, 58mm f&b tb, 1.7 rr, electric fan, jm longtube headers, B&M hammer shifter, Cope Racing Trans, Viper Brakes, SRT8 Seats, nx wet kit(100 shot)
best time 11.32 @ 118 1.59 60' on spray(old motor). 11.76@115 n/a(new motor)
DD 07 SRT8 Charger 12.55@112
well I have a manual trans so Idk about the kickdown cable for sure but I think it would snap on, but the 8018 stud will fit on the throttle cable but because its on the bottom of the linkage I wouldn't think it to be ideal for that purpose, youd have to have the throttle cable mounted to pull from the rear, or mount the entire tbody backwards to make it pull the right direction
1995 Dakota Club Cab, 408, 5spd, 8 3/4 rear end
i think the only difference from the holley 20-40 mentioned earlier and the edelbrock 8018 stud is the threads that or on the mounting part, the stud size is the same
1995 Dakota Club Cab, 408, 5spd, 8 3/4 rear end
Got everything mocked up for the 4bbl install, the stock IAC fits with ovaling out one hole, but it isn't extended enough to seal the IAC port, and I don't know if its bottomed out yet. Other than that everything is going rather smoothly
Mods - TB Spacer, Short Throw Dipstick, Performance Auto Zone Intake "0.30 over bore", R/T Cam, Performance Chip, Radiator Delete
Rev limiter? that's what valve springs are for!
When you power up the iac it should "self adjust". That manifold needs some coating or something dude.
Planning on putting my 4bb setup on my pig next week finally....
Josh - 98 BLK RC - Mad Milkshake Maker
Previous
99 BLK RC - Mad Trash Hauler - sold
99 DA RC - mad dak - Danno Stole it
01 SLVR RC - mad sexy - retired - then died
99 IB RC - mad RT - gone to heaven..
Former Certified member of the 11 Second NA RT Club
Mods - TB Spacer, Short Throw Dipstick, Performance Auto Zone Intake "0.30 over bore", R/T Cam, Performance Chip, Radiator Delete
Rev limiter? that's what valve springs are for!
Osee
Forgive me if I missed this. What mods did you do to the motor your putting it on? I ordered a M1 4BBL intake from PEI should have it next week it comes with the 2BBL adapter but would rather run a 4BBL throttle body. Just started this build Do you think the 4BBL would be to much for a 5.9 .30 over w/cam high flow heads & a tune? I was thinking of building a stroker but I think its over kill for my Jeep Grand Cherokee 4x4.
Uhhhhhh there are much more knowledgeable people than me, so hopefully they can chime in. I believe a 58mm tb is rated at 1200 cfm aswell, so it would be an equivalent. With a EFI engine the velocity in the plenum is less of an issue because the fuel is atomizing at the end of the intake runner rather than the top of the intake. With that being said I know guys were putting "turtles" in their m1 intakes back in the day so I don't really know. I think an eddy headed 360 should be fine, the throttle body is a progressive rate tb as well so it'll help tip in performance, and should in theory help prevent stumbling.
my plan is just stock short block, .565 .565 218/224, 1.92 valves, adj rr's, spintech longs, m1 4bbl, 4bbl tb, and nitrous until the snow flies. then in the winter, T56 swap, and vortech v1 install and keep turning it up until it pops.
Mods - TB Spacer, Short Throw Dipstick, Performance Auto Zone Intake "0.30 over bore", R/T Cam, Performance Chip, Radiator Delete
Rev limiter? that's what valve springs are for!
Osee
I'm sure you will but keep us posted, I'd love to know how it runs once installed.
Thanks
I dont know about everyone else but my throttle is like an on/off switch now. Its like going from a 1/4 throttle to wot once the secondary blades open. Not terrible by any means, but more sensitive than with just the 2 blades
410, 10.3 comp pistons, P&P Eddies, 254 cam, 30lb injectors, sct tuner, 3800 viper stall, 4:56 yukon gears, hotchkis tvs, m1 4brrl, 58mm f&b tb, 1.7 rr, electric fan, jm longtube headers, B&M hammer shifter, Cope Racing Trans, Viper Brakes, SRT8 Seats, nx wet kit(100 shot)
best time 11.32 @ 118 1.59 60' on spray(old motor). 11.76@115 n/a(new motor)
DD 07 SRT8 Charger 12.55@112
i guess I don't really feel that way.. don't get me wrong, you KNOW it when the second blades open, but if I'm at 3/4 throttle and then push it further it accelerates harder... and I think that at under half throttle it is easier to control as well. love that secondary linkage, you can feel It in the pedal when you are half way open so you know you are about to open the next barrels. I have the accel 1350 for comparison if you are using one of the other ones
1995 Dakota Club Cab, 408, 5spd, 8 3/4 rear end
I do some fab work but yours knocks the ball out of the park,,great job. I'm just starting to do the same build,, where did you get fuel rails also fuel line fitting ?? Thanks-great job...
Just bought same one from- AT Racing-they use other names,, they told me 87 Mustang 5.0 ltr. TPS ??
Speed master sells an adapter for the TPS. .. just ordered one.. told to use 87 mustang 5.0 TPS by speed master ??