+ Reply to Thread
Results 1 to 10 of 10

Thread: DYNO 02 R/T Light Mod

  1. #1

    darkenedrt's Avatar
    Senior Member

    Status
    Offline
    Join Date
    Mar 2013
    Location
    Norman, Oklahoma
    Posts
    1,259

    Default DYNO 02 R/T Light Mod

    Went to a Mopar get together at a local shop and got my truck on the dyno today. Mods are: Modified Kegger Intake, Hughes 52MM TB, CAI, Mid-Length Headers, Exhaust. It was running way rich. It started at around 12.5 but dropped to about 10.5-11 in the higher RPM. Definitely need a tune...

    But it didn't do half bad to say the least! 230RWHP/321 FT-LBS





    Next mod I'm thinking is a little shot of nitrous....

    Videos

    Here's the one where I recorded the live data. Notice the drop in the A/F ratio.
    https://youtu.be/cwNjxVqLP9s

    And my first pull where it did the best run
    https://youtu.be/_RhaP5EOpls
    Last edited by darkenedrt; 06-06-2015 at 05:14 AM.

  2. #2


    krs1r/t's Avatar
    want more inchs STROKE IT

    Status
    Offline
    Join Date
    Aug 2009
    Location
    vineland, nj
    Posts
    5,863

    Default

    A lot left on the table with air/fuels looking like that. Still nice work You will love it after a good tune

    Bad Luck Truck
    Current setup
    „R„block 429ci W5 heads 700hp N/A
    1/8 mile #'s 6.47@105 1.37 60’ 10.23@131

    Old 1/4 numbers below with 408
    Fastest N/A 2010,2011,2014
    477-RWHP ?-RWTQ

    11.244 ET @ 119.71mph N/A
    FOXHOLE RACING
    "If you like me good, if you hate me, even better!"
    Chris

  3. #3


    OG DRTC

    Status
    Offline
    Join Date
    Jan 2008
    Location
    Bellevue, NE
    Posts
    6,856

    Default

    Get an M1 on that thing.


  4. #4


    99dart's Avatar
    Senior Member

    Status
    Offline
    Join Date
    Feb 2008
    Location
    Washington...the hot side!
    Posts
    3,886

    Default

    I got my best 60's with a modded kegger. If the engine isn't built for turning higher rpms, this is a great mod.
    99 DA CC R/T
    13.97@100 w/modded kegger & ported TB
    12.96 @103
    10:8-1 .30 over forged bottom end
    R/T ported heads
    Detroit locker 4:56 gears
    Built 46RE MSaine 3500 stall Ultra Billet
    http://imgur.com/a/lOVuZ

  5. #5


    Broo42's Avatar
    Senior Member

    Status
    Offline
    Join Date
    Jul 2012
    Location
    Yukon, OK
    Posts
    2,050

    Default

    The numbers surprised the hell out of me. You have a pretty good starting point. Ditch the cat, get an M1, and a tune!

    I was also surprised with the difference in numbers between the 2 Hellcats that were there.
    2004 SRT4 Moar Pah Coming DD
    2002 Dakota R/T 12.376@110.84


    "Is there any way to make this easier? I'm way confused now. I just tried to post a video, but instead I got my dick caught in the ceiling fan" Wyotech_Cuda440

  6. #6


    slvr03dakrt's Avatar
    make it bigger STROKE IT

    Status
    Offline
    Join Date
    Jan 2008
    Location
    Memphis, TN
    Posts
    2,491

    Default

    Quote Originally Posted by Broo42 View Post
    The numbers surprised the hell out of me. You have a pretty good starting point. Ditch the cat, get an M1, and a tune!

    I was also surprised with the difference in numbers between the 2 Hellcats that were there.
    What we're the numbers?


    Forged 408 12.10 @ 111mph under the knife again

  7. #7


    Broo42's Avatar
    Senior Member

    Status
    Offline
    Join Date
    Jul 2012
    Location
    Yukon, OK
    Posts
    2,050

    Default

    Quote Originally Posted by slvr03dakrt View Post
    What we're the numbers?
    The first 1 made 607/585 and the other made 650/???. The car with the higher number only had about 1900 miles on it.
    2004 SRT4 Moar Pah Coming DD
    2002 Dakota R/T 12.376@110.84


    "Is there any way to make this easier? I'm way confused now. I just tried to post a video, but instead I got my dick caught in the ceiling fan" Wyotech_Cuda440

  8. #8

    darkenedrt's Avatar
    Senior Member

    Status
    Offline
    Join Date
    Mar 2013
    Location
    Norman, Oklahoma
    Posts
    1,259

    Default

    Yeah the cat is going away soon as well as the shit Flowmaster. Definitely a tune after I get the exhaust nightmare squared away.

  9. #9
    g3ar's Avatar
    Senior Member

    Status
    Offline
    Join Date
    Aug 2014
    Location
    Austin tx
    Posts
    108

    Default

    look at all that torque from not having the m1 on yet ....get that exhaust how you want it with some rockers ignition work and a programmer..I say stick with the chopped keg if its done right and your not doing internal work

  10. #10
    Junior Member

    Status
    Offline
    Join Date
    Feb 2013
    Location
    Seattle, WA.
    Posts
    7

    Default

    Good numbers!

    Mine put down 232hp I believe with same mods except stock tb and a Hughes intake manifold. I know my tps was bad also which may or may not have affected my numbers. I know mine was rich also like yours. I would love to see what mine would do now with a mild cam, roller rockers and a tune.

+ Reply to Thread

Posting Permissions

  • You may post new threads
  • You may post replies
  • You may not post attachments
  • You may not edit your posts
  •