Thanks Warmer tomorrow (55) have 16 rings to file fit and maybe wash it up a little ,might as well get stuff done while i'm layed off
Thanks Warmer tomorrow (55) have 16 rings to file fit and maybe wash it up a little ,might as well get stuff done while i'm layed off
i am working on my dakota truck and my durango, also i bought a very nice Ford Bronco xlt 1993 with the 5.8l windsor . the truck has very low miles no rust nothing and it looks like new inside and outside .
-Dodge Durango 4x2 1999 5.9l
-Dodge Dakota 1993 2.5l
-Ford Bronco XLT 5.8L 1993
My truck really needed a bath due to all of the pollen and shit the trees are dropping.
All the coin-op car washes in my town are closed except for one in the opposite (sketchy) side of town. So I gave her a bath!
2003 CC
360 Swapped, FRP Tuned, 2.02 EQ Heads, 210XP cam, HS 1.7 RR's, Fastman 52mm TB, Mopar 2bbl M1, Mopar/PPH Headers, 2.5" True Dual, X-Pipe, Hooker AeroChambers, Hi Flow Cats, MSD Coil, Cloyes Double Roller Chain, JGC fan, 180F T-stat, Mopar Valve covers, K&N FIPK, PATC 2800 Stall, Martin Saine VB, Mildly built trans, 4.10 gears.
249 HP/322 TQ FRP Tune (Old build. New build TBD)
12.35 @ 109 (150 Shot)
#1222
r/DodgeDakota
Hoping to pick up some metal for my chassis jig this week.
Odd looking car wash also! I picked up a 1700 psi Greenworks pressure washer,(electric) havnt used it yet though
Gave her a little wash today, definitely need to pick up some new headlights/ parking and taillights, might throw the buffer pad on tomorrow, also got the Jeep all cleaned up
BCB990B7-6CDC-46B9-A321-FFE95936BC26.jpg
1F269F8A-AAFE-46BC-BD70-8E5F583B00C2.jpg
D9784660-0E8F-4477-9178-7214F8D0CE7C.jpg
To the buff pad to the first half of the truck and got the Jeep flossing
7182FBA5-BD9C-419D-9DF5-FD037B221B2E.jpg
D8F4A2BB-99CF-4028-AA62-C357064EADC5.jpg
They're looking great, Ernie! I'm playing catch up after being gone so long. Working on a couple things on the back of the motorhome before backing it up against the fence.
99 DA CC R/T
13.97@100 w/modded kegger & ported TB
12.96 @103
10:8-1 .30 over forged bottom end
R/T ported heads
Detroit locker 4:56 gears
Built 46RE MSaine 3500 stall Ultra Billet
http://imgur.com/a/lOVuZ
Oh... I charged my battery! LOL
99 DA CC R/T
13.97@100 w/modded kegger & ported TB
12.96 @103
10:8-1 .30 over forged bottom end
R/T ported heads
Detroit locker 4:56 gears
Built 46RE MSaine 3500 stall Ultra Billet
http://imgur.com/a/lOVuZ
20200426_105933.jpg20200426_105636.jpg
Couple photos while i'm waiting on intake bolts and header bolts and other stuff( ARP stuff is sloooooww) Photo 1 is that oil filter adapter for picking oil pressure for the twin turbos without the clutter around the gauge location. i'm going to put 90's on so they don't stick out so far when they come in. And the other pic is edelbrocks 1000 CMF throttle body i see a few talking about ( Pro Flo 4 is not made with an magnum style intake but parts including a stand alone computer can be bought seperatly) . Good day yesterday got all the rings filed and installed bottom end is all torqued and sealed up with returns installed. i must be getting old it took me 12 hours to get it done.
Last edited by Wideopen; 04-26-2020 at 03:48 PM. Reason: spelling
Looking good ! I had to swap the alternator on the Jeep Friday night, 3-4 hour job in 45 mins, while bbqing and drinking beer lol
8FD320C8-B56C-4166-80F8-6C4B03AFD40B.jpg
3483EC57-7C06-4E71-A26C-0A39C270FCC0.jpg
Got the headers back on, the coolant temperature sending unit in, cooling system filled back up, some more wiring mock up done, and did some adjusting on the carb for easier cold start.
'03 R/T CC - 1969 440 - 0.040" over, 10.73:1 static
Forged crank | Molnar billet rods | Diamond Racing forged pistons | Fluidampr | Meziere 35gpm | Performer RPM | Brawler 750cfm | Whiplash cam | Aeromotive 90gph | MSD HVC
Got the 4.56 gears in today what a job. Had an issue with the pin hitting the edge of the tooth and not going in straight so I hit the corner of the tooth (nowhere near the contact patch ) with the grinder and got it done and works great only need more power now lol
Ya you know I though of that lol but i don't think this old engine can take more then 150 shot. I have won 3 races so far but I'm real careful not to bite off to much fo my little 400 hp monster I could go to 300 shot because other engine is getting real close to the finish line . Cant wait. 3rd victim was a mustang with a 150 shot on street radials he was still spinning when I crossed the 1/8 mark so i just got my jegs order on his bank roll lol Was my first dead pony with this little RT
I can pick up from ARP and get a 15% Discount... but it’s actually cheaper to order from Summit Racing if I get the $100 free shipping. After a few visits I found out Summit has more in stock too! My nearest Summit is in Nevada, but I get bolts next day to SoCal.
ARP now has 1/8 increments in their bolts, not on their site yet, but a salesperson was able to get me what I needed and said they’ll advertise them this year.
Their main hub is maybe a mile from my house and factory is about 15miles away.
12.10@106@Famoso Raceway
Nice its taken 5 days to get intake bolts, header bolts and rocker shaft bolts here in MI. Maybe JEGS is getting ARP stuff dropped shipped. I don't mind waiting on the good stuff because i've never had one fail me yet
Nothing on the truck but I put a TB in the Jeep, had it cleaned out quite a bit
399E7F1C-A432-4F3D-9324-9718AA5A54D6.jpg
2003 CC
360 Swapped, FRP Tuned, 2.02 EQ Heads, 210XP cam, HS 1.7 RR's, Fastman 52mm TB, Mopar 2bbl M1, Mopar/PPH Headers, 2.5" True Dual, X-Pipe, Hooker AeroChambers, Hi Flow Cats, MSD Coil, Cloyes Double Roller Chain, JGC fan, 180F T-stat, Mopar Valve covers, K&N FIPK, PATC 2800 Stall, Martin Saine VB, Mildly built trans, 4.10 gears.
249 HP/322 TQ FRP Tune (Old build. New build TBD)
12.35 @ 109 (150 Shot)
#1222
r/DodgeDakota
I shift at 4900 lol but that would be fun converter if I was keeping the current setup I'm just playing with the youngsters who think there junks fast lol
4K would put your spray right in play at WIDEOPEN throttle ! So w/ the gears it would definitely launch hard
Yes it would till I scattered the trans all over the road lol I'd just be happy to turn off the stock rev limiter so I don't hit it on the spray. The reason why I shift early is it's at 5300 by the time it grabs another gear. I'm running a TCI 727 on other engine with trans brake so I belive that converter wouldn't work for that set up. This is a daily drivin street truck lol
20200429_183335.jpg valve train installed