+ Reply to Thread
Page 1 of 3 1 2 3 LastLast
Results 1 to 25 of 58

Thread: HPTuners for Dodge

  1. #1

    Senior Member

    Status
    Offline
    Join Date
    Feb 2008
    Location
    Greenwich, CT
    Posts
    530

    Thumbs up HPTuners for Dodge

    Not sure if anyone on here has HPTuners but they now have the ability to scan our trucks. I was able to get a very good readout of my fuel trims, o2 sensor voltage, timing, etc and sent that all over to hemifever and he was able to get my tune spot on without needing a wideband. They are currently working on the capability to actually edit the software in our pcms so that we could just go on a laptop, make changes and update it. Only problem is that its been taking a long time. If we can get a bunch of you guys to go on the HPTuners forum and express your interest in getting this done, hopefully it will make it happen sooner. Below is the link to their forum where the techs post regularly. If we could get this to happen soon we could have tuning that blows away everything else currently out there. Below is the link to the Dodge HPTuners just create a username and post up your interest on there.

    http://www.hptuners.com/forum/showthread.php?t=17396

    K&N Gen 2
    F&B 55x52mm
    M1 4bbl ported
    SCT/Hemifever
    Crower 1.7RR & Lifters
    PPH Headers
    2½ Magnaflow xpipe/mufflers
    Accel Cap/Rotor/Coil
    Brembos & Hawks
    MSD 8.5mm Wires
    NGK 4291s
    Meziere 170º stat
    224/230 536/544 110+4
    ShadyDell Stage 3 Eddys
    Hotchkis/Bilstien
    4.56's/Detroit TruTrac
    MSaine 46re
    Viper 3600 stall
    Eagle F1 235/50f
    MT 305/45r

    345hp & 350ft-lbs SAE
    12.7@108mph

  2. #2
    Senior Member

    Status
    Offline
    Join Date
    Jan 2008
    Location
    Too close to DC
    Posts
    5,124

    Default

    That sounds like they were just reading the ODBII data stream. I'd be surprised if they could actually toon it.
    03 CC 4.7 NV3500

  3. #3

    Senior Member

    Status
    Offline
    Join Date
    Feb 2008
    Location
    Greenwich, CT
    Posts
    530

    Default

    Quote Originally Posted by mtlcafan79 View Post
    That sounds like they were just reading the ODBII data stream. I'd be surprised if they could actually toon it.
    thats basically what it is except it comes out in a really good graph form that can be saved onto the computer, emailed, and then used to update the pcm with the sct tuner. So basically I was able to get my truck tuned without needing to go back and forth to the dyno and without a wideband and it was spot on. What I am trying to get them to do that they have been working on for years is to get us the ability to actually tune with the software so that if we want to make changes to our tune we can do it whenever we want and so that we will have more parameters to change than wat SCT currently offers.

    K&N Gen 2
    F&B 55x52mm
    M1 4bbl ported
    SCT/Hemifever
    Crower 1.7RR & Lifters
    PPH Headers
    2½ Magnaflow xpipe/mufflers
    Accel Cap/Rotor/Coil
    Brembos & Hawks
    MSD 8.5mm Wires
    NGK 4291s
    Meziere 170º stat
    224/230 536/544 110+4
    ShadyDell Stage 3 Eddys
    Hotchkis/Bilstien
    4.56's/Detroit TruTrac
    MSaine 46re
    Viper 3600 stall
    Eagle F1 235/50f
    MT 305/45r

    345hp & 350ft-lbs SAE
    12.7@108mph

  4. #4



    Senior Member

    Status
    Offline
    Join Date
    Feb 2008
    Location
    Corrales, New Mexico
    Posts
    17,958

    Default

    I was just on the HP tuner web site...Where's the Dodge?
    11.27 @ 118.23
    2017 NM Mopar Challenge Series Champion

  5. #5

    Default

    Ernie at Westech used HPTuners to datalog my truck while it was on the dyno, but he still had to write the tunes in SCT and load them through the handheld.

    It did work pretty nice though, the HPtuners program was on his laptop and gathered data pretty good, then he just clicked over to the SCT software, tweaked the tune and loaded it in the handheld.

    Drops panties faster than any R/T

  6. #6

    Senior Member

    Status
    Offline
    Join Date
    Feb 2008
    Location
    Greenwich, CT
    Posts
    530

    Default

    Quote Originally Posted by Adobedude View Post
    I was just on the HP tuner web site...Where's the Dodge?
    click this link : http://www.hptuners.com/forum/forumdisplay.php?f=27 thats all dodge stuff. just post on there your interest in them getting us some tuning abilities to go along with their scanning. the more people we get to express interest the sooner we will get some better tuning capabilities than wats out there now

    K&N Gen 2
    F&B 55x52mm
    M1 4bbl ported
    SCT/Hemifever
    Crower 1.7RR & Lifters
    PPH Headers
    2½ Magnaflow xpipe/mufflers
    Accel Cap/Rotor/Coil
    Brembos & Hawks
    MSD 8.5mm Wires
    NGK 4291s
    Meziere 170º stat
    224/230 536/544 110+4
    ShadyDell Stage 3 Eddys
    Hotchkis/Bilstien
    4.56's/Detroit TruTrac
    MSaine 46re
    Viper 3600 stall
    Eagle F1 235/50f
    MT 305/45r

    345hp & 350ft-lbs SAE
    12.7@108mph

  7. #7

    Senior Member

    Status
    Offline
    Join Date
    Feb 2008
    Location
    Greenwich, CT
    Posts
    530

    Default

    Quote Originally Posted by wyotech_cuda440 View Post
    Ernie at Westech used HPTuners to datalog my truck while it was on the dyno, but he still had to write the tunes in SCT and load them through the handheld.

    It did work pretty nice though, the HPtuners program was on his laptop and gathered data pretty good, then he just clicked over to the SCT software, tweaked the tune and loaded it in the handheld.
    yea thats basically what i did. the hptuners scanner is a big plus but im trying to get people together to express interest so that we can tune our own vehicles and have more parameters to adjust than what sct currently offers which is not much at all.

    K&N Gen 2
    F&B 55x52mm
    M1 4bbl ported
    SCT/Hemifever
    Crower 1.7RR & Lifters
    PPH Headers
    2½ Magnaflow xpipe/mufflers
    Accel Cap/Rotor/Coil
    Brembos & Hawks
    MSD 8.5mm Wires
    NGK 4291s
    Meziere 170º stat
    224/230 536/544 110+4
    ShadyDell Stage 3 Eddys
    Hotchkis/Bilstien
    4.56's/Detroit TruTrac
    MSaine 46re
    Viper 3600 stall
    Eagle F1 235/50f
    MT 305/45r

    345hp & 350ft-lbs SAE
    12.7@108mph

  8. #8



    Senior Member

    Status
    Offline
    Join Date
    Feb 2008
    Location
    Corrales, New Mexico
    Posts
    17,958

    Default

    I saw the forum, I don't see a scanner lister for our trucks. I might be interested in a scanner for data logging for now but I have an FAST XFI waiting in the wings
    11.27 @ 118.23
    2017 NM Mopar Challenge Series Champion

  9. #9


    Blown and Squirted

    Status
    Offline
    Join Date
    Jan 2008
    Location
    SE PA
    Posts
    8,150

    Default

    The SCT handheld doesnt do this? Jesus christ..... what a ripoff.

    '99 R/T- MSIIextra fuel/spark/idle, ZCP mx422 supercharged, ZCP Tbrake 727, PPC 10" 3800, 4.10, (\/) Headers, 2.5" Duals, Truetrac, Boyd Timeless 6's, Hotchkis TVS.
    Z Code Performance Website

  10. #10

    Senior Member

    Status
    Offline
    Join Date
    Feb 2008
    Location
    Greenwich, CT
    Posts
    530

    Default

    sct handheld does not scan. the hptuners device is a scanner/programmer all in one. it scans our trucks.

    K&N Gen 2
    F&B 55x52mm
    M1 4bbl ported
    SCT/Hemifever
    Crower 1.7RR & Lifters
    PPH Headers
    2½ Magnaflow xpipe/mufflers
    Accel Cap/Rotor/Coil
    Brembos & Hawks
    MSD 8.5mm Wires
    NGK 4291s
    Meziere 170º stat
    224/230 536/544 110+4
    ShadyDell Stage 3 Eddys
    Hotchkis/Bilstien
    4.56's/Detroit TruTrac
    MSaine 46re
    Viper 3600 stall
    Eagle F1 235/50f
    MT 305/45r

    345hp & 350ft-lbs SAE
    12.7@108mph

  11. #11

    Senior Member

    Status
    Offline
    Join Date
    Feb 2008
    Location
    Greenwich, CT
    Posts
    530

    Default

    http://www.hptuners.com/order.php thats the link. you can either can the entire interface which i have for $499 because i use it to tune my trans am but if you dont want that you can get just the scanner for $349. id get the whole thing though because whenever they do come out with tuning it will be right there. you can also get the pro one if you want to connect external devices like wideband.

    K&N Gen 2
    F&B 55x52mm
    M1 4bbl ported
    SCT/Hemifever
    Crower 1.7RR & Lifters
    PPH Headers
    2½ Magnaflow xpipe/mufflers
    Accel Cap/Rotor/Coil
    Brembos & Hawks
    MSD 8.5mm Wires
    NGK 4291s
    Meziere 170º stat
    224/230 536/544 110+4
    ShadyDell Stage 3 Eddys
    Hotchkis/Bilstien
    4.56's/Detroit TruTrac
    MSaine 46re
    Viper 3600 stall
    Eagle F1 235/50f
    MT 305/45r

    345hp & 350ft-lbs SAE
    12.7@108mph

  12. #12



    Senior Member

    Status
    Offline
    Join Date
    Feb 2008
    Location
    Corrales, New Mexico
    Posts
    17,958

    Default

    Still don't see a Dodge listed...
    11.27 @ 118.23
    2017 NM Mopar Challenge Series Champion

  13. #13

    Senior Member

    Status
    Offline
    Join Date
    Feb 2008
    Location
    Greenwich, CT
    Posts
    530

    Default

    Quote Originally Posted by Adobedude View Post
    Still don't see a Dodge listed...
    no dodge listed because dodge credits for tuning cannot be bought. it can only be used as a scanner right now so you dont need credits to scan a vehicle.

    K&N Gen 2
    F&B 55x52mm
    M1 4bbl ported
    SCT/Hemifever
    Crower 1.7RR & Lifters
    PPH Headers
    2½ Magnaflow xpipe/mufflers
    Accel Cap/Rotor/Coil
    Brembos & Hawks
    MSD 8.5mm Wires
    NGK 4291s
    Meziere 170º stat
    224/230 536/544 110+4
    ShadyDell Stage 3 Eddys
    Hotchkis/Bilstien
    4.56's/Detroit TruTrac
    MSaine 46re
    Viper 3600 stall
    Eagle F1 235/50f
    MT 305/45r

    345hp & 350ft-lbs SAE
    12.7@108mph

  14. #14

    Default

    Quote Originally Posted by Adobedude View Post
    Still don't see a Dodge listed...
    It's just an OBD II data logger program and cable for your laptop. It can data log on any OBD II vehicle.

    They are currently working on tuning software for dodge, so that you can data log and tune at the same time with one program, but it's not available yet.

    It is a very nice datalogging system, but it's a bit pricey. For the pro scanner and wideband it's $750. Whenever they release the tuning software, you'll be able to upgrade and tune your own truck.

    Drops panties faster than any R/T

  15. #15

    Senior Member

    Status
    Offline
    Join Date
    Feb 2008
    Location
    Greenwich, CT
    Posts
    530

    Default

    Quote Originally Posted by wyotech_cuda440 View Post
    It's just an OBD II data logger program and cable for your laptop. It can data log on any OBD II vehicle.

    They are currently working on tuning software for dodge, so that you can data log and tune at the same time with one program, but it's not available yet.

    It is a very nice datalogging system, but it's a bit pricey. For the pro scanner and wideband it's $750. Whenever they release the tuning software, you'll be able to upgrade and tune your own truck.
    thats the key word lol. WHEN. it couldnt be sooner

    K&N Gen 2
    F&B 55x52mm
    M1 4bbl ported
    SCT/Hemifever
    Crower 1.7RR & Lifters
    PPH Headers
    2½ Magnaflow xpipe/mufflers
    Accel Cap/Rotor/Coil
    Brembos & Hawks
    MSD 8.5mm Wires
    NGK 4291s
    Meziere 170º stat
    224/230 536/544 110+4
    ShadyDell Stage 3 Eddys
    Hotchkis/Bilstien
    4.56's/Detroit TruTrac
    MSaine 46re
    Viper 3600 stall
    Eagle F1 235/50f
    MT 305/45r

    345hp & 350ft-lbs SAE
    12.7@108mph

  16. #16
    Senior Member

    Status
    Offline
    Join Date
    Jan 2008
    Location
    Too close to DC
    Posts
    5,124

    Default

    I think it's more like IF.
    03 CC 4.7 NV3500

  17. #17



    Senior Member

    Status
    Offline
    Join Date
    Feb 2008
    Location
    Corrales, New Mexico
    Posts
    17,958

    Default

    Quote Originally Posted by mtlcafan79 View Post
    I think it's more like IF.
    I agree...
    11.27 @ 118.23
    2017 NM Mopar Challenge Series Champion

  18. #18




    huskerrt79's Avatar
    Majestic Motorsports

    Status
    Offline
    Join Date
    Apr 2008
    Location
    NC
    Posts
    4,228

    Default

    Would be nice to have some cometition between tuning platforms though. not just the one.
    Sales Manager at Majestic Motorsports

    712 rwhp, 650 rwtq 2009 Pontiac G8

    Best Run in Dak: 10.89 @ 126.79
    DRTC Member #1092

  19. #19
    99408kotar/t's Avatar
    Senior Member

    Status
    Offline
    Join Date
    Jun 2008
    Location
    Crown Point, IN
    Posts
    2,164

    Default

    Its at least a nice datalogging option. Seems like it would be easier to log with this than the innovative stuff.
    410, 10.3 comp pistons, P&P Eddies, 254 cam, 30lb injectors, sct tuner, 3800 viper stall, 4:56 yukon gears, hotchkis tvs, m1 4brrl, 58mm f&b tb, 1.7 rr, electric fan, jm longtube headers, B&M hammer shifter, Cope Racing Trans, Viper Brakes, SRT8 Seats, nx wet kit(100 shot)
    best time 11.32 @ 118 1.59 60' on spray(old motor). 11.76@115 n/a(new motor)
    DD 07 SRT8 Charger 12.55@112

  20. #20

    BryanRT360's Avatar
    Dirty Jerzey

    Status
    Offline
    Join Date
    Jan 2008
    Location
    south jersey
    Posts
    6,039

    Default

    Quote Originally Posted by Five9Dak View Post
    The SCT handheld doesnt do this? Jesus christ..... what a ripoff.
    Stupid truck would've went 11.5s if it did
    2002 AB CC R/T (R.I.P)
    11.52@116.61 w/1.67 60'.

    2002 AB QC 4.7 4x4


    www.schroermasonry.com
    Facebook.com/SchroerMasonry

  21. #21




    huskerrt79's Avatar
    Majestic Motorsports

    Status
    Offline
    Join Date
    Apr 2008
    Location
    NC
    Posts
    4,228

    Default

    Quote Originally Posted by BryanRT360 View Post
    Stupid truck would've went 11.5s if it did
    Lol,
    Sales Manager at Majestic Motorsports

    712 rwhp, 650 rwtq 2009 Pontiac G8

    Best Run in Dak: 10.89 @ 126.79
    DRTC Member #1092

  22. #22

    Senior Member

    Status
    Offline
    Join Date
    Feb 2008
    Location
    Greenwich, CT
    Posts
    530

    Default

    so how bout it guys would some of you take the time to post up your interest on that site? wont take more than 5 minutes of your time

    K&N Gen 2
    F&B 55x52mm
    M1 4bbl ported
    SCT/Hemifever
    Crower 1.7RR & Lifters
    PPH Headers
    2½ Magnaflow xpipe/mufflers
    Accel Cap/Rotor/Coil
    Brembos & Hawks
    MSD 8.5mm Wires
    NGK 4291s
    Meziere 170º stat
    224/230 536/544 110+4
    ShadyDell Stage 3 Eddys
    Hotchkis/Bilstien
    4.56's/Detroit TruTrac
    MSaine 46re
    Viper 3600 stall
    Eagle F1 235/50f
    MT 305/45r

    345hp & 350ft-lbs SAE
    12.7@108mph

  23. #23
    99408kotar/t's Avatar
    Senior Member

    Status
    Offline
    Join Date
    Jun 2008
    Location
    Crown Point, IN
    Posts
    2,164

    Default

    ill try and get over there
    410, 10.3 comp pistons, P&P Eddies, 254 cam, 30lb injectors, sct tuner, 3800 viper stall, 4:56 yukon gears, hotchkis tvs, m1 4brrl, 58mm f&b tb, 1.7 rr, electric fan, jm longtube headers, B&M hammer shifter, Cope Racing Trans, Viper Brakes, SRT8 Seats, nx wet kit(100 shot)
    best time 11.32 @ 118 1.59 60' on spray(old motor). 11.76@115 n/a(new motor)
    DD 07 SRT8 Charger 12.55@112

  24. #24

    Senior Member

    Status
    Offline
    Join Date
    Feb 2008
    Location
    Greenwich, CT
    Posts
    530

    Default

    Quote Originally Posted by 99408kotar/t View Post
    ill try and get over there
    thanks. duner already posted up on there if he reads this thanks duner. someone else also posted up on there who i think is from these forums.

    K&N Gen 2
    F&B 55x52mm
    M1 4bbl ported
    SCT/Hemifever
    Crower 1.7RR & Lifters
    PPH Headers
    2½ Magnaflow xpipe/mufflers
    Accel Cap/Rotor/Coil
    Brembos & Hawks
    MSD 8.5mm Wires
    NGK 4291s
    Meziere 170º stat
    224/230 536/544 110+4
    ShadyDell Stage 3 Eddys
    Hotchkis/Bilstien
    4.56's/Detroit TruTrac
    MSaine 46re
    Viper 3600 stall
    Eagle F1 235/50f
    MT 305/45r

    345hp & 350ft-lbs SAE
    12.7@108mph

  25. #25
    99408kotar/t's Avatar
    Senior Member

    Status
    Offline
    Join Date
    Jun 2008
    Location
    Crown Point, IN
    Posts
    2,164

    Default

    i have voiced my complaint haha
    410, 10.3 comp pistons, P&P Eddies, 254 cam, 30lb injectors, sct tuner, 3800 viper stall, 4:56 yukon gears, hotchkis tvs, m1 4brrl, 58mm f&b tb, 1.7 rr, electric fan, jm longtube headers, B&M hammer shifter, Cope Racing Trans, Viper Brakes, SRT8 Seats, nx wet kit(100 shot)
    best time 11.32 @ 118 1.59 60' on spray(old motor). 11.76@115 n/a(new motor)
    DD 07 SRT8 Charger 12.55@112

+ Reply to Thread
Page 1 of 3 1 2 3 LastLast

Posting Permissions

  • You may post new threads
  • You may post replies
  • You may not post attachments
  • You may not edit your posts
  •