Closed Thread
Page 3 of 3 FirstFirst 1 2 3
Results 51 to 65 of 65

Thread: Tips on pulling the engine...to speed up process.

  1. #51
    Senior Member

    Status
    Offline
    Join Date
    Feb 2008
    Location
    Central Kentucky
    Posts
    5,154

    Default

    At this point, seeing what grapejuice did, I think I'll try taking the intake off. Then I'll be able to get the hook/chains down low to lift the engine out and clear things. I think I'll pull the elec fan, throw a board in there to protect rad and see if it'll work.

    I don't want to have to align body parts if I can avoid it. Tried that in the past and it was difficult at the time.
    The Dakota RT is gone... but not forgotten.

    '15 Granite Crystal Metallic SRT 392.

  2. #52
    RJ_Hythloday's Avatar
    Complete part out

    Status
    Offline
    Join Date
    Nov 2009
    Location
    Providence, UT
    Posts
    1,085

    Default

    Quote Originally Posted by Intense RT View Post
    At this point, seeing what grapejuice did, I think I'll try taking the intake off. Then I'll be able to get the hook/chains down low to lift the engine out and clear things. I think I'll pull the elec fan, throw a board in there to protect rad and see if it'll work.

    I don't want to have to align body parts if I can avoid it. Tried that in the past and it was difficult at the time.
    uggh,, I'm not looking forward to getting my front bumper realigned. I was supposed to get the gutter guard in the valance while it was off. I started w/ my beer keg on, and quickly removed it. I'll be leaving the M1 off till the engine is in. I'm going to use the old dizzy cap, and stock valve covers for install also.
    360 ,52mm F&B, M1, EQ heads bronze valve liners, mpp valve train, KRC Custom Ground Cam, Crower 1.7's, PPH midlength, SCT Hemifever tuning, LM-2, 2 1/2" duals

    EQ heads

    Complete part out 99 Durango w/ 5.9


  3. #53

    Default

    im done with mine, pulled the motor last saturday, sunday got the new motor in, with 2-3 hrs for 3 days got everything done, today i tried to start but come to find out i had the distributor 180, got 40 miles on it so far.
    Brad
    00 CC IB sport 360
    98 RC white sport mildly worked v6, used as a truck!

  4. #54
    Senior Member

    Status
    Offline
    Join Date
    Feb 2008
    Location
    Central Kentucky
    Posts
    5,154

    Default

    I'm not seeing how one would get the distributor 180 out? Installing timing chain and not putting #1 at TDC when aligning the slot on the intermediate shaft to front intake bolt on driver's side?

    I did this on the 408, albeit carbed, and it fired right up with the wires in stock orientation on the cap. Missing something?

    I'm about to do this in the next week or so and want to make sure it goes smoothly. Gonna scribe a mark in the block and dist. base to keep the fuel sync real close to where it is now. +1 or 2
    The Dakota RT is gone... but not forgotten.

    '15 Granite Crystal Metallic SRT 392.

  5. #55
    RJ_Hythloday's Avatar
    Complete part out

    Status
    Offline
    Join Date
    Nov 2009
    Location
    Providence, UT
    Posts
    1,085

    Default

    So here's a question I have.

    On the way out we turned the crank to gain access to each bolt that holds the flex plate onto the torque converter. The conv just slips on, couldn't I just put the flex plate and converter on the engine while it's on the hoist?
    360 ,52mm F&B, M1, EQ heads bronze valve liners, mpp valve train, KRC Custom Ground Cam, Crower 1.7's, PPH midlength, SCT Hemifever tuning, LM-2, 2 1/2" duals

    EQ heads

    Complete part out 99 Durango w/ 5.9


  6. #56

    Default

    Quote Originally Posted by RJ_Hythloday View Post
    So here's a question I have.

    On the way out we turned the crank to gain access to each bolt that holds the flex plate onto the torque converter. The conv just slips on, couldn't I just put the flex plate and converter on the engine while it's on the hoist?
    I don't think this would be a good idea, the converter does slip on but you have to turn it and will feel/hear it click a few times two or three, can't remember now. Also it should be pre-filled so that would be a mess. Another thing is it's pretty heavy.

  7. #57
    RJ_Hythloday's Avatar
    Complete part out

    Status
    Offline
    Join Date
    Nov 2009
    Location
    Providence, UT
    Posts
    1,085

    Default

    Quote Originally Posted by Last_in View Post
    I don't think this would be a good idea, the converter does slip on but you have to turn it and will feel/hear it click a few times two or three, can't remember now. Also it should be pre-filled so that would be a mess. Another thing is it's pretty heavy.
    Ok, sounds good. I was wondering if I needed to top it off w/ some ATF+4
    360 ,52mm F&B, M1, EQ heads bronze valve liners, mpp valve train, KRC Custom Ground Cam, Crower 1.7's, PPH midlength, SCT Hemifever tuning, LM-2, 2 1/2" duals

    EQ heads

    Complete part out 99 Durango w/ 5.9


  8. #58



    grapejuice1998's Avatar
    Send Lawyers Guns & Money

    Status
    Offline
    Join Date
    Jan 2008
    Location
    Dallas, TX
    Posts
    9,739

    Default

    Quote Originally Posted by RJ_Hythloday View Post
    So here's a question I have.

    On the way out we turned the crank to gain access to each bolt that holds the flex plate onto the torque converter. The conv just slips on, couldn't I just put the flex plate and converter on the engine while it's on the hoist?
    Flex plate yes, converter, no.

    Like Last In said, be sure the converter is all the way seated before you install the motor. Push in, turn, push in, turn, repeat until you feel it clunk into place, then push it all the way back against the case. Be sure to put a jack under the front of the transmission to help you line things up as you drop the motor in.
    Alan Short
    D.R.T.C. #15


  9. #59



    grapejuice1998's Avatar
    Send Lawyers Guns & Money

    Status
    Offline
    Join Date
    Jan 2008
    Location
    Dallas, TX
    Posts
    9,739

    Default

    Quote Originally Posted by Intense RT View Post
    I'm not seeing how one would get the distributor 180 out? Installing timing chain and not putting #1 at TDC when aligning the slot on the intermediate shaft to front intake bolt on driver's side?

    I did this on the 408, albeit carbed, and it fired right up with the wires in stock orientation on the cap. Missing something?

    I'm about to do this in the next week or so and want to make sure it goes smoothly. Gonna scribe a mark in the block and dist. base to keep the fuel sync real close to where it is now. +1 or 2
    The distributor drive is slotted, so it's easy to get it in 180 out and just as easy to lift up and correct it.
    There is a notch on the distributor body that lines up with the rotor tip, which sets the fuel sync to somewhere around zero. Be sure half shaft is clocked right in the oil pump though. It should point at the front, inside corner of the drivers side valve cover. Looking down on it, that should look about like 11 o clock/5:00 o clock.
    Alan Short
    D.R.T.C. #15


  10. #60



    grapejuice1998's Avatar
    Send Lawyers Guns & Money

    Status
    Offline
    Join Date
    Jan 2008
    Location
    Dallas, TX
    Posts
    9,739

    Default

    Quote Originally Posted by Intense RT View Post
    At this point, seeing what grapejuice did, I think I'll try taking the intake off. Then I'll be able to get the hook/chains down low to lift the engine out and clear things. I think I'll pull the elec fan, throw a board in there to protect rad and see if it'll work.

    I don't want to have to align body parts if I can avoid it. Tried that in the past and it was difficult at the time.
    You'll need to remove the cap/wires/rotor and the crank pulley. Also, the hood to firewall gasket that seals the hood off at the cowl. The hood will either have to be removed, or what I do is remove the bolts, put something under each rear edge to protect the paint, then strap the hood up past where the hinges would stop it.
    It's a tight squeeze, but it'll come out/go back in.
    Alan Short
    D.R.T.C. #15


  11. #61
    Senior Member

    Status
    Offline
    Join Date
    Feb 2008
    Location
    Central Kentucky
    Posts
    5,154

    Default

    Quote Originally Posted by grapejuice1998 View Post
    The distributor drive is slotted, so it's easy to get it in 180 out and just as easy to lift up and correct it.
    There is a notch on the distributor body that lines up with the rotor tip, which sets the fuel sync to somewhere around zero. Be sure half shaft is clocked right in the oil pump though. It should point at the front, inside corner of the drivers side valve cover. Looking down on it, that should look about like 11 o clock/5:00 o clock.
    I finished last week. I used a scribe to mark the block deeply with a casting parting line in the body of the dist to keep fuel sync correct before disassembly. Remembered from the 408 to line up with intake/valve cover bolt area...just got the rotor lined up with the tab sticking out from dist body. Fired right up.
    The Dakota RT is gone... but not forgotten.

    '15 Granite Crystal Metallic SRT 392.

  12. #62



    grapejuice1998's Avatar
    Send Lawyers Guns & Money

    Status
    Offline
    Join Date
    Jan 2008
    Location
    Dallas, TX
    Posts
    9,739

    Default

    Quote Originally Posted by Intense RT View Post
    I finished last week. I used a scribe to mark the block deeply with a casting parting line in the body of the dist to keep fuel sync correct before disassembly. Remembered from the 408 to line up with intake/valve cover bolt area...just got the rotor lined up with the tab sticking out from dist body. Fired right up.
    That's a really good feeling when they fire right up and settle into a nice idle.
    Alan Short
    D.R.T.C. #15


  13. #63

    Hugh Jassole's Avatar
    Shoo Shoo Retarded Flu !!

    Status
    Offline
    Join Date
    Jan 2008
    Location
    Deep in the Swamps of Jersey
    Posts
    7,310

    Default

    Quote Originally Posted by grapejuice1998 View Post
    That's a really good feeling when they fire right up and settle into a nice idle.

    sure is, then it runs for 3 minutes and goes boom !

  14. #64
    RJ_Hythloday's Avatar
    Complete part out

    Status
    Offline
    Join Date
    Nov 2009
    Location
    Providence, UT
    Posts
    1,085

    Default

    Quote Originally Posted by Special Ed's R/T - Yaaaay View Post
    sure is, then it runs for 3 minutes and goes boom !
    My wife would KILL me. Literally. Not even kidding!
    360 ,52mm F&B, M1, EQ heads bronze valve liners, mpp valve train, KRC Custom Ground Cam, Crower 1.7's, PPH midlength, SCT Hemifever tuning, LM-2, 2 1/2" duals

    EQ heads

    Complete part out 99 Durango w/ 5.9


  15. #65

    Default

    can someone make this thread a sticky? lots of good info esp for someone who hasnt done a motor swap.
    Brad
    00 CC IB sport 360
    98 RC white sport mildly worked v6, used as a truck!

Closed Thread
Page 3 of 3 FirstFirst 1 2 3

Posting Permissions

  • You may post new threads
  • You may post replies
  • You may not post attachments
  • You may not edit your posts
  •