Search:

Type: Posts; User: GoFastGray

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Other option is to change out the bearings on...

    Other option is to change out the bearings on wheels to accommodate to your axles. Another $20 for amazon bearings...
  2. Also interested in the kit for Bogart users...

    Also interested in the kit for Bogart users :biggthumpup:
  3. Replies
    2
    Views
    1,035

    From Hi-Potek? I haven't used it. Not sure what...

    From Hi-Potek?
    I haven't used it. Not sure what parts I had Martin Saine upgrade or what I upgraded when I rebuilt by daily trans. Assuming you have to pull everything back apart to adjust it?
  4. Thread: Msd instal

    by GoFastGray
    Replies
    3
    Views
    4,316

    Allows you to pull timing/spark instead of fuel...

    Allows you to pull timing/spark instead of fuel when you hit the rev limiter. Little safer on the engine. Just have to tune/bump the stock map higher than what you're limit is with MSD.
  5. Eddy heads here as well. I haven't lined my belt...

    Eddy heads here as well. I haven't lined my belt up yet but didn't notice anything being off.
    Maybe you need to take some measurements and mill down some spacers.
  6. Thread: Msd instal

    by GoFastGray
    Replies
    3
    Views
    4,316

    Still on my to-do list, but I see Holley makes a...

    Still on my to-do list, but I see Holley makes a nice harness for our trucks.
    https://www.holley.com/products/electrical/harnesses/parts/8884
  7. Replies
    3
    Views
    5,593

    It has been done. I have a set to do myself and...

    It has been done. I have a set to do myself and seen a couple out there.
  8. Thread: T-Dolly

    by GoFastGray
    Replies
    6
    Views
    2,905

    Future project for you, or something that will be...

    Future project for you, or something that will be available to all in future?
  9. Replies
    10
    Views
    1,379

    Maybe a short arm will help then? Just make sure...

    Maybe a short arm will help then? Just make sure you have full engagement so that you don't strip the hex. You can buy or modify your own....
  10. Replies
    10
    Views
    1,379

    Yes, anti-seize with aluminum to stainless is a...

    Yes, anti-seize with aluminum to stainless is a MUST! I rarely install ANY bolt without anti-seize or some sort of thread sealant anymore.
  11. Replies
    10
    Views
    1,379

    I ran ARP bolts for my Spintech headers. They...

    I ran ARP bolts for my Spintech headers. They sell "Reduced Wrenching" bolts that have a smaller hex head which help for clearance issues. A 3/8-16 Hex head bolt generally uses a 9/16 wrench. ARP...
  12. Replies
    8,427
    Views
    2,269,902

    $365 for Belltech's was easy enough to slap them...

    $365 for Belltech's was easy enough to slap them in and call it a day. Sits about 1" higher though.
    I do plan to take the Hotchkis springs to a shop and have them ressurect them one day. Just didn't...
  13. Replies
    8,427
    Views
    2,269,902

    Yea, if you look closely at the broken piece, it...

    Yea, if you look closely at the broken piece, it looks as though half was already partially split (rusted).
  14. Replies
    8,427
    Views
    2,269,902

    YEP! I forgot about the crossing too, don't ever...

    YEP! I forgot about the crossing too, don't ever travel on that stretch. New-ish paved road by my work (45mph zone). Smooth road with normal looking crossing until you go over it. Co-worker felt like...
  15. Replies
    8,427
    Views
    2,269,902

    Ordered some Belltech 3" drop leaf springs for...

    Ordered some Belltech 3" drop leaf springs for the daily. My Hotchkis leafs didn't hold up well to a f'kd up railroad crossing.:fml:

    16448
  16. Upgrade to your truck, or do you have a donor you...

    Upgrade to your truck, or do you have a donor you use to mock up all your new gadgets?
  17. Replies
    103
    Views
    12,262

    What brand did you end up using and from where?

    What brand did you end up using and from where?
  18. Replies
    8,427
    Views
    2,269,902

    Get rails from Richard? Mine's been basically...

    Get rails from Richard?
    Mine's been basically parked since that last Sacramento meet. (Or one race after that). Slowly adding goodies to her.
  19. Thread: Help please

    by GoFastGray
    Replies
    3
    Views
    1,432

    You can also buy a plate to replace stock one....

    You can also buy a plate to replace stock one. They are a little pricey and I personally would invest in a better manifold VS installing one of these. (But it's an option)
    ...
  20. Thread: Fuel sync??

    by GoFastGray
    Replies
    11
    Views
    2,129

    Set to 0 to +4. My tuner recommends +4, I believe...

    Set to 0 to +4. My tuner recommends +4, I believe my daily was happier at +2 with similar mods to what you have.
    Dealer should also be able to set it, not sure what they charge.
  21. Replies
    5
    Views
    1,099

    Yea, I would have given you a couple hundred for...

    Yea, I would have given you a couple hundred for them...
  22. Replies
    3
    Views
    3,587

    9-years later... I'd say fat chance, but can...

    9-years later... I'd say fat chance, but can contact him if interested.
    Might also want to post a WANTED add for it or even search FB classified groups for one.
  23. Replies
    5
    Views
    1,099

    Strip or Strip/Street?

    Strip or Strip/Street?
  24. Replies
    2
    Views
    896

    What's the standard for run-out tolerance on...

    What's the standard for run-out tolerance on valves?
  25. Replies
    8,427
    Views
    2,269,902

    I should have tried the V6 model, but the one I...

    I should have tried the V6 model, but the one I have is still working fine.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4