Search:

Type: Posts; User: ddrango

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    31
    Views
    12,903

    A carbon fiber covered fiberglass one piece back...

    A carbon fiber covered fiberglass one piece back window plate would suffice. :biggthumpup:
  2. Replies
    64
    Views
    16,767

    Get a ScanGauge II

    Get a ScanGauge II
  3. The Dakota R/T is NOT on the list ...

    The Dakota R/T is NOT on the list

    http://www.gtplanet.net/forum/showthread.php?t=86724

    It's a possibility though.
  4. Replies
    6
    Views
    2,546

    .100%.

    .100%.
  5. Replies
    50
    Views
    11,594

    Any idea where these valve cover spacers are??...

    Any idea where these valve cover spacers are?? Haven't found them
  6. Here are my fall shots! Clicky...

    Here are my fall shots!

    Clicky
  7. Replies
    4
    Views
    1,901

    03/04 front spindles, 03/04 front calipers &...

    03/04 front spindles, 03/04 front calipers & rotors (that match the vehicle the spindles came off of), die grinder to grind down the end of your brake line mount.

    Did it a few times on people's...
  8. Replies
    32
    Views
    9,280

    Thanks you Dave :biggthumpup: Hope all is well...

    Thanks you Dave :biggthumpup: Hope all is well with you
  9. Replies
    32
    Views
    9,280

    I guess I'll think about throwing my M1 on this...

    I guess I'll think about throwing my M1 on this motor in the spring...it's been sitting in my room for two years now.
  10. Replies
    32
    Views
    9,280

    It's a 4bbl.

    It's a 4bbl.
  11. Replies
    32
    Views
    9,280

    True, but the M1 is for my 426. Hmm...I...

    True, but the M1 is for my 426.



    Hmm...I think I'm going to try 89 just for the heck of it. I don't really drive the truck much anymore, but I'll give it a shot. I'm going to overhaul that...
  12. Replies
    32
    Views
    9,280

    Definitely burning oil...got codes for pre cat...

    Definitely burning oil...got codes for pre cat sensors, so in the spring I'm ripping the barrel off and cleaning up. Damn belly pan!
  13. Replies
    32
    Views
    9,280

    Ok, it's definitely the oil then. My manifold's...

    Ok, it's definitely the oil then. My manifold's belly pan gasket has been horribly blown for a little over a year now. It's so bad I would most definitely gain a couple of tenths fixing it.

    Might...
  14. Replies
    32
    Views
    9,280

    Really? You think I should use the 89 tune?

    Really? You think I should use the 89 tune?
  15. Replies
    32
    Views
    9,280

    Very brief slideshow of this weekend

    Very limited on time these past few weeks, my fathers ill again and is pulling through yet again. He goes into surgery in the morning.

    Anyway, this past weekend I managed to get to the track for...
  16. Replies
    5
    Views
    2,287

    Well Hotchkis lists that the leaf springs with...

    Well Hotchkis lists that the leaf springs with the four plates will drop a R/T 2 1/4" out back, and without the plates it will drop a R/T 1 1/4" out back. So I used no plates (1 1/4") and used WC...
  17. Replies
    4
    Views
    2,296

    My truck seems to have more rear bite than front...

    My truck seems to have more rear bite than front bite now with 03' R/T rear brakes and 02' front brakes.

    When my bud did the brakes he clamped the single main line coming to the distribution block...
  18. Replies
    5
    Views
    2,287

    I had 3" blocks on R/t leafs, and went to...

    I had 3" blocks on R/t leafs, and went to Hotchkis leafs (no plates or anything) with the 2" rear hangers, and I'm almost 2" higher than I used to be! According to Hotchkis manual on the leaf...
  19. Replies
    5
    Views
    2,287

    For some odd reason they appeared to not give me...

    For some odd reason they appeared to not give me any drop on my truck, I can't figure it out. I'm not sure if I'm going to put 1" blocks or the front hangers from WC that I have on. If anything, if...
  20. Replies
    10
    Views
    3,293

    LoL, really??

    LoL, really??
  21. Replies
    3
    Views
    1,947

    My bro has the whole kit and he cut his own...

    My bro has the whole kit and he cut his own exhaust holes into it, if you're interested I'll talk to him about it.
  22. Replies
    37
    Views
    12,753

    owned

    owned
  23. Replies
    5
    Views
    2,123

    Ok sir, I'm sure they're 18", I mean he can't be...

    Ok sir, I'm sure they're 18", I mean he can't be wrong it's his ad.
  24. Replies
    5
    Views
    2,123

    Too bad those are 17"

    Too bad those are 17"
  25. Thread: Bedrug

    by ddrango
    Replies
    35
    Views
    11,326

    You got that right Chas! The beds of EVERY Dakota...

    You got that right Chas! The beds of EVERY Dakota ever made to this day are identical. Only difference with the older ones (Gen1 &2) is that they're narrower. Good find though! How you been? Hows...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4