Search:

Type: Posts; User: Duner

Page 1 of 20 1 2 3 4

Search: Search took 0.23 seconds.

  1. Jack the truck up from the driver’s side to try...

    Jack the truck up from the driver’s side to try and get as much trans fluid away from the switch as possible....or you will be wearing a bunch of it.:biggthumpup:
  2. Just another off-hand thought.... if it’s a new...

    Just another off-hand thought....
    if it’s a new build - how good are the grounds?
    Make sure there is no paint under the grounds, or it will have very weak spark, poor performance and not run under...
  3. I would double check the distributor position /...

    I would double check the distributor position / cam sync. It sounds like it could be off, but that wouldn’t explain a sooty #2 plug.

    That sounds like the cam I am running, and with PCM I ran cam...
  4. Thread: Rear tires

    by Duner
    Replies
    25
    Views
    2,305

    They work better than my normal street tires........

    They work better than my normal street tires.....
    but they aren’t any sort of “miracle” or anything.
    Just “better”.

    At the track I can run 11’s with them instead of 12’s or 13’s on street tires....
  5. Replies
    10
    Views
    728

    Well, you first put a roll bar behind the seat -...

    Well, you first put a roll bar behind the seat - then the seat is just a couple of inches closer to the dash....then you rub your shins against the dash while you drive it and enjoy the close fit!
  6. Thread: Rear tires

    by Duner
    Replies
    25
    Views
    2,305

    I concur that drag radials are WAY more effective...

    I concur that drag radials are WAY more effective at hooking up on the street than normal tires are.
  7. Replies
    36
    Views
    2,560

    My go-to to make power is still boost. If you...

    My go-to to make power is still boost.
    If you only want 400 - a blower is easy.
    WAY easier than engine swaps.
  8. Replies
    158
    Views
    13,837

    We don’t build any DAKOTA parts, but we build...

    We don’t build any DAKOTA parts, but we build fixtures and jigs for all the parts we manufacture over and over again. They don’t change
  9. Replies
    50
    Views
    3,969

    I still swing by here occasionally. Still no...

    I still swing by here occasionally. Still no fagbook for me.

    Hey man it's ME DAVE.....let me in!
  10. Replies
    15
    Views
    1,427

    It sounds like it's going all over your tailgate...

    It sounds like it's going all over your tailgate after leaking out.
  11. Thread: New new PB

    by Duner
    Replies
    9
    Views
    1,760

    Very nice!

    Very nice!
  12. Nice job!

    Nice job!
  13. Replies
    8,258
    Views
    799,497

    Very nice.

    Very nice.
  14. Replies
    8,258
    Views
    799,497

    I'm glad you didn't hit anything either! And...

    I'm glad you didn't hit anything either!

    And yes, what a mess.
  15. Replies
    8,258
    Views
    799,497

    Thanks. it was good luck - other than cleanup.

    Thanks.
    it was good luck - other than cleanup.
  16. Replies
    8,258
    Views
    799,497

    I posted about this earlier this week - but it...

    I posted about this earlier this week - but it must have gotten lost in the reboot/recover site deal.

    I managed to put on a nice big smoke show this week on my way into work in the black...
  17. No problem! 236/242 cam still gives me power...

    No problem!
    236/242 cam still gives me power brakes and A/C controls.

    My pistons are .005" out of the hole, with .052" thick Cometics. I couldn't get them at .045".
  18. Like everybody already said - camshaft is a very...

    Like everybody already said - camshaft is a very big part of the equation.

    As a young lad - I tried 12.5:1 with a stock cam. That thing pinged on premium at idle.
  19. Replies
    2
    Views
    1,145

    That should go fast.

    That should go fast.
  20. Thread: New PB!

    by Duner
    Replies
    23
    Views
    2,892

    Congrats on the new best!!!!!! That ALWAYS...

    Congrats on the new best!!!!!!

    That ALWAYS feels good to see progress.
  21. Replies
    16
    Views
    2,438

    My wing at that angle cost me 2 mph at the...

    My wing at that angle cost me 2 mph at the stripe.
    I thought it looked cool - but it's not staying if it slows the truck down.
  22. Replies
    20
    Views
    2,528

    BIG congrats Dave! Well Done!

    BIG congrats Dave!
    Well Done!
  23. Replies
    29
    Views
    1,922

    At work - I write myself notes to help me...

    At work - I write myself notes to help me remember what I'm supposed to be doing..... then I forget where I left the notes and then I'm completely lost! LOL

    As for parts that are squirreled...
  24. Replies
    23
    Views
    1,645

    I go out for 100 or 200 mile street romps - with...

    I go out for 100 or 200 mile street romps - with the AC and stereo blasting!
  25. Replies
    23
    Views
    1,645

    I'll usually run mine for a whole 300 miles!...

    I'll usually run mine for a whole 300 miles! hahaha
    That gives me a chance to take a look at them.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4