Search:

Type: Posts; User: DodgeSqD

Page 1 of 11 1 2 3 4

Search: Search took 1.22 seconds.

  1. Replies
    1
    Views
    6,827

    I don't come very often ,could you contact me at...

    I don't come very often ,could you contact me at rohr911@gmail.com
    To purchase these .
    Thanks Larry.
  2. I'm getting ready to order some more Candence...

    I'm getting ready to order some more Candence QRS6.5 coaxial speakers to go allong with these Candence CMVs 6" components with a Thunderfourm sub box . I'll need 2 amps to run this set up . A 300 .2...
  3. Nice work

    Nice work
  4. Replies
    8
    Views
    7,702

    Well my procedure doesn't cost anything .

    Well my procedure doesn't cost anything .
  5. Replies
    8
    Views
    7,702

    You may need to reset the stepper motor count . "...

    You may need to reset the stepper motor count . " the IAC is what I'm talking about .
    Unplug the IAC . then plug the vent for the IAC . Then start the engine and adjust the idle set screw to 650...
  6. I have one of these transmissions. Still in its...

    I have one of these transmissions. Still in its shipping crate.
    When my 05 MSaine goes this will get its VB. then installed.
  7. Replies
    50
    Views
    37,107

    Mouth breather here cocksucker. LoL Not on here...

    Mouth breather here cocksucker. LoL
    Not on here much, 3-4 times a month
  8. Replies
    7
    Views
    8,641

    Nice truck Dead fish. LOL

    Nice truck Dead fish. LOL
  9. Replies
    8,427
    Views
    2,269,982

    Finally . It's in, but the flange on the right...

    Finally . It's in, but the flange on the right down tube needs to be clocked to install the exhaust .
    Larry
  10. Replies
    6
    Views
    7,916

    Welcome

    Welcome
  11. Replies
    30
    Views
    20,989

    Are you near Red Bluff Ca .its a stop I make...

    Are you near Red Bluff Ca .its a stop I make every few months .
  12. On your issue with the lever against the...

    On your issue with the lever against the fuelrail.
    Cut a 1/8th thick aluminum plate to fit under your throttle body
    Use a gasket for a template.
  13. Replies
    20
    Views
    5,768

    Never mind the what's this and what's that .a...

    Never mind the what's this and what's that .a solid lifter with a pushrod checking tool and the correct roller tip pattern accross the valve tip ,is all that matters . When ever anything is changed...
  14. Replies
    3
    Views
    1,471

    First thing to check for when doing electical on...

    First thing to check for when doing electical on an older vehicle is that all grounds are clean and tight . If in droubt add a ground strap. If the switch is getting hot , the new bulbs my draw too...
  15. Replies
    20
    Views
    5,768

    You need to make your lifter solid . Remove the...

    You need to make your lifter solid . Remove the internals of your lifter and make a shim out of a bolt and nut , I used a 5/16 x 1" hex bolt from my header . Adjust the nut so when you drop the cup...
  16. Replies
    4
    Views
    7,231

    I don't know any other way , sorry as a last...

    I don't know any other way , sorry as a last resort ,pull the interior from where the door meets the strike bar , drill out the mounting bolts
  17. Replies
    8,427
    Views
    2,269,982

    I 've been keeping up with your build for some...

    I 've been keeping up with your build for some time . Congrats on your championship . These heads flow enough for the build I'm finishing ,and I did try a set of Jesel rockers on this motor they...
  18. Replies
    4
    Views
    7,231

    If it was me , I would pull the door panel off...

    If it was me , I would pull the door panel off the passenger side and and close the latch with the door open and figure out how to open it from inside the door its self..
  19. Replies
    8,427
    Views
    2,269,982

    Yes, the heads were worked over by the Fastman's...

    Yes, the heads were worked over by the Fastman's guy back in 05 ,and yea they have taller height valves .My shimms are .250 thousands tall .Now I can order my pushrods. And when I get back in a...
  20. Replies
    8,427
    Views
    2,269,982

    Got my block back from the machine shop . Spent...

    Got my block back from the machine shop . Spent the day dry fitting the motor , and now ill be able to order the pushrods.
  21. Replies
    8,427
    Views
    2,269,982

    Some engine pics

    Some engine pics
  22. Replies
    8,427
    Views
    2,269,982

    These pics were taken at Rich's house when he...

    These pics were taken at Rich's house when he showed me the truck in Ohio . Included is a cool rendention of Fred and Wilma
  23. Replies
    30
    Views
    20,989

    How close are you to Red Bluff CA . Ill be there...

    How close are you to Red Bluff CA .
    Ill be there on sunday .
  24. Replies
    30
    Views
    20,989

    How close are you to Red Bluff CA .

    How close are you to Red Bluff CA .
  25. Replies
    8,427
    Views
    2,269,982

    Let me try this

    Let me try this
Results 1 to 25 of 270
Page 1 of 11 1 2 3 4