Search:

Type: Posts; User: slvr03dakrt

Page 1 of 20 1 2 3 4

Search: Search took 0.09 seconds.

  1. Replies
    23
    Views
    5,191

    Ive dealt with richard at hipotek and he is top...

    Ive dealt with richard at hipotek and he is top notch. Ive dealt with indy and it there was a little more to be desired. Hughes i know alot of people give them a bad rap but i had them fix and port a...
  2. Replies
    24
    Views
    7,152

    Hi powered rifle will take care of that. Cough...

    Hi powered rifle will take care of that. Cough cough ar 15
  3. Replies
    59
    Views
    21,289

    I would go bigger on the cam. I built a 408 with...

    I would go bigger on the cam. I built a 408 with a 228/230 cam and it was all done at 5600rpm and had tons of tq. It paired nicely with a 2800 converter and had great street manners and decent mpg.
  4. Damn on track for a 20 yr build

    Damn on track for a 20 yr build
  5. Replies
    8,427
    Views
    2,269,937

    I was fixing to say projected tip and nitrous...

    I was fixing to say projected tip and nitrous dont mix.
  6. Replies
    87
    Views
    53,348

    Ask Dstoots about that.

    Ask Dstoots about that.
  7. Replies
    104
    Views
    38,645

    Nice build, boost is going to wake it up on the...

    Nice build, boost is going to wake it up on the bottom end. What heads are you running?
  8. Replies
    7
    Views
    1,988

    I ground the head down to about half the...

    I ground the head down to about half the thickness. I never had any issues
  9. Replies
    9
    Views
    2,637

    Normally people run a steel top ring for heavy...

    Normally people run a steel top ring for heavy nitrous. But a moly faced ring for ocasional nitrous use is ok the ring gap needs to be opened up a little but should say in the ring pack based on the...
  10. But as far as compressed gasket thickness you...

    But as far as compressed gasket thickness you will prob need to find something .055 to .060 thick i always like to have right at .040 quench. Hence why i always zero decked my motors and ran a .039...
  11. So you brought the piston up to zero deck...

    So you brought the piston up to zero deck verified by the straight edge across the bore. Then set a dail indicator at 0 then contiued to rotate the end and it read .015 past zero. Sounds good to me.
  12. Replies
    7
    Views
    2,393

    Obama can suck me

    Obama can suck me
  13. Replies
    89
    Views
    26,239

    Well i blew my shit up once bc i cheaped out on...

    Well i blew my shit up once bc i cheaped out on a cast stroker crank. It was only a 5 grand mistake.
  14. Replies
    23
    Views
    9,547

    Was it a one hit wonder?

    Was it a one hit wonder?
  15. Replies
    23
    Views
    6,278

    Start with a 75 hit and if all goes well jet it...

    Start with a 75 hit and if all goes well jet it up. Read the plugs they will tell the tale also an Afr Guage is good to have.
  16. Replies
    58
    Views
    15,173

    High 12s or low 12s.

    High 12s or low 12s.
  17. Remove it for sure. When it sits just make sure...

    Remove it for sure. When it sits just make sure you put in gear and let it sit for a second before depressing the gas.
  18. Replies
    12
    Views
    7,134

    It's all about making a few extra dollars.

    It's all about making a few extra dollars.
  19. Replies
    41
    Views
    12,277

    It ain't doing any good sitting on the kitchen...

    It ain't doing any good sitting on the kitchen counter. Get to work and get it put on.
  20. Replies
    9
    Views
    3,279

    Looks good I miss my silver 2003 I had....

    Looks good I miss my silver 2003 I had. :dumbass234: should of kept it.
  21. Replies
    4
    Views
    1,805

    Yea might wanna post basic specs bc I can't see...

    Yea might wanna post basic specs bc I can't see the cam card very good
  22. Replies
    25
    Views
    6,116

    Yep stock computer with sct custom tune will take...

    Yep stock computer with sct custom tune will take you along way. I'd step up to a good set of heads and cam to let that stroker breath. I think the best street setup is a set of blended Eddie heads...
  23. Replies
    21
    Views
    6,127

    Drill it out completely and helicoil it

    Drill it out completely and helicoil it
  24. Replies
    20
    Views
    9,507

    For 32k I can make 1000+hp with less headache.

    For 32k I can make 1000+hp with less headache.
  25. Replies
    15
    Views
    6,531

    I took it up to the local auto shop with the...

    I took it up to the local auto shop with the springs off the truck and walked in the back door with a 10 dolla bill put them on the press and said I need these bushings in here and 3 mins later I...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4