Nice work, I'll be ordering one soon.
Type: Posts; User: 2dakotas
Nice work, I'll be ordering one soon.
The single plane LA EFI Edelbrock intake should do the trick, but may need a little porting to take advantage of these heads. Also, you could use the Indy LA intake drilled for injectors.
IMM...
I'm still around and drive mine almost daily. I'm starting to gather parts for an interesting upgrade :secret squirrel:. Nah, I don't care who knows, I'm gathering parts for a Gen3 Hemi swap in my...
If it is a 2001 and newer, you will need load resistor for each bulb, or you will get hyper flashing. I believe the 97-00 trucks can use a simple led flasher to prevent hyper flash. If you have to...
Ordered Hemi motor mounts from Schumacher :secret squirrel:
Those welds :biggthumpup:
Thanks for all the info.
Thanks for the input. That actually pretty much made my mind up now. I want something a little stiffer than stock springs, so I've been eyeing the belltech springs to get the drop and a little better...
I've always loved your Gen2. Quick question, I think I remember you doing Belltech spindles. I have heard mixed review on them, with a lot of people getting bad bump steer with wider tires. How is...
Not an RT, but I picked this jewel up yesterday. 94, 318, 5 speed, power windows and locks, bucket seats, and console. It has 127k miles, and I got it for $2300.
14993
14994
A problem I am struggling with, it would take a lot of $$$$ to get the same flow out of a Magnum style head, as a stock 6.1 head. I am going stand alone either way, so electronics will be about the...
Thanks guys. Like I said in the original post, I'm strongly considering a hemi swap now anyway. I'm thinking 6.1 with my D1SC Procharger would make a fun ride.
14917
14918
I had a piston come apart. There are a couple marks in the number 6 cylinder, but I think .030 to .040 would clean it up. However, there is a small chunk taken out of the bottom of that cylinder...
No, I've run 27" tall tires for years on my truck. It shifted fine when I still had the auto, and no ABS light. 275 50 17 is also close to 28 in height, and aren't crazy expensive.
A little update, after a week of driving. The ride is as good, if not slightly better. The handling is slightly better also. Keep in mind, I still have the stock Bilsteins, so with proper shocks,...
It's just 2" blocks right now. However I'm about to change to something else, as I hate blocks. They were on the truck when I got but I've never bothered to change them out yet, but I will soon.
I don't have much feedback yet, as I only drove it about 10 miles so far. However, so far it does feel like the steering is tighter.
I didn't put the rubber isolators in with the new springs,...
Took the western chassis control arms with stock springs off. I replaced with stock control arms and Hotchkis 1912f springs.
I know, but you have a big smile after it's done. Did you come come up with any new cuss words, or promise you would never modify a vehicle again?
It was either the heater box or duct work under the dash that was in the way. It needed about 1 more inch clearance to have slid right in. I've not actually done it on a pre-01, but I haven't heard...
You can just swap the rod and pedals. However, on 01 and newer, get ready to come up with new cuss words. It is a PITA to do. I ended up still almost taking the whole assembly out, just to get the...
This...
Thanks Richard! Also, I will be buying your feed and return fittings when I do my return system in the near future.
What size is the fuel line fitting at the fuel pump? I know the line size itself is 5/16, but I have heard conflicting information concerning the fitting size itself. I have heard 3/8 and I have...