Search:

Type: Posts; User: nitroram33

Page 1 of 20 1 2 3 4

Search: Search took 0.25 seconds; generated 27 minute(s) ago.

  1. Replies
    23
    Views
    4,841

    :rockwoot:

    :rockwoot:
  2. :rockwoot:

    :rockwoot:
  3. Replies
    32
    Views
    10,340

    I'm using stock '98 everything (except brakes,...

    I'm using stock '98 everything (except brakes, obviously, but that's all Mustang stuff) with '03 spindles without issue. For the record, the spindles DO press out if you ever need them to.
    ...
  4. Replies
    18
    Views
    1,501

    Not ever going to be 100% clean thanks to the PCV...

    Not ever going to be 100% clean thanks to the PCV valve and breather (correction it's the breather going into the hat and the PCV dumping into the side of the intake), but there's going to be a lot...
  5. Replies
    18
    Views
    1,501

    PCV valve dumps oil vapors into the airhat above...

    PCV valve dumps oil vapors into the airhat above the throttle blades. A belly pan gasket blowout will causing pooling a quite a bit of oil on the intake floor. The belly pan everyone is talking...
  6. Replies
    18
    Views
    1,501

    You'd see a ton of oil puddled if it was the...

    You'd see a ton of oil puddled if it was the belly pan. It's definitely not leaking out the bottom? Is the tip of the exhaust black? If the exhaust is black and there's nothing on the ground it's...
  7. Can I vote to call them exhaust turtles lol?...

    Can I vote to call them exhaust turtles lol? :jester:
  8. Replies
    12
    Views
    15,111

    Plausible lol

    Plausible lol
  9. Replies
    12
    Views
    15,111

    Looked in my user manual (10k Bendpak symetric...

    Looked in my user manual (10k Bendpak symetric 2-post) and 4.25" is their minimum (6" recommended) in concrete cured for at least 28 days and at least 6" from cracks or seams. Looking on their site,...
  10. Replies
    12
    Views
    15,111

    You can do a lot of things lol. 4" is fine for a...

    You can do a lot of things lol. 4" is fine for a 4 post and if you're not picking up anything heavy you can probably even get away with it for a two post if you do the anchor bolts correctly. ...
  11. Replies
    4
    Views
    3,357

    :rockwoot:

    :rockwoot:
  12. Replies
    12
    Views
    15,111

    Recommended depth is usually 6" for a ~10k pound...

    Recommended depth is usually 6" for a ~10k pound 2 post. My shop is 8" except for under where the lift lives. There it dips down to a little over a foot with extra rebar in the trench. Better safe...
  13. Replies
    21
    Views
    13,559

    :rockwoot:

    :rockwoot:
  14. Replies
    8,427
    Views
    2,270,004

    Yes? 3" for normal trucks, 2" for R/Ts. ...

    Yes? 3" for normal trucks, 2" for R/Ts.

    https://www.belltech.com/products/belltech/lowering/components/leaf-springs/belltech-3-quot-drop-rear-leaf-spring-each-5983.html
  15. Replies
    8,427
    Views
    2,270,004

    :r/t smile:

    :r/t smile:
  16. :dumbass234:

    :dumbass234:
  17. Replies
    19
    Views
    7,313

    You're close enough to visit him in person, it's...

    You're close enough to visit him in person, it's always the people that can't do that who have bad experiences with him.
  18. Replies
    19
    Views
    7,313

    PIE is only useful if you're close enough to show...

    PIE is only useful if you're close enough to show up to his shop in Delaware. Anybody outside of driving distance has always had a bad time.
  19. The Rampage is also not a replacement for the...

    The Rampage is also not a replacement for the Dakota. It's Maverick/Santa Cruz-sized. A mid-sized Dakota replacement (ie Tacoma/Ranger/Colorado etc competitor) is in development completely separate...
  20. Replies
    19
    Views
    7,313

    Ryan is in Texas and your best bet. Don't waste...

    Ryan is in Texas and your best bet. Don't waste your time with Hemifever.
  21. The Rampage, as designed, is purely a South...

    The Rampage, as designed, is purely a South American vehicle. If it were to come to that states it would have to be built in North America to avoid the chicken tax. It would also have to move to a...
  22. :biggthumpup:

    :biggthumpup:
  23. :biggthumpup:

    :biggthumpup:
  24. Replies
    103
    Views
    12,264

    :r/t smile:

    :r/t smile:
  25. :r/t smile:

    :r/t smile:
Results 1 to 25 of 494
Page 1 of 20 1 2 3 4