Search:

Type: Posts; User: Miggity

Page 1 of 11 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    5
    Views
    8,667

    *** sold ***

    *** sold ***
  2. Replies
    5
    Views
    8,667

    Bump for edits and new asking price.

    Bump for edits and new asking price.
  3. Replies
    5
    Views
    8,667

    00' 408 CC R/T - Southeast VA

    Well gents it's been a fun ride but I'm tired of watching my R/T collect dust. She needs to go to a good home where the tires will be properly roasted and she can get the TLC she so desperately...
  4. Replies
    18
    Views
    3,253

    The 555s are looking better and better.

    The 555s are looking better and better.
  5. Replies
    18
    Views
    3,253

    I ran 255/50 KDWS about 8 years ago. I went back...

    I ran 255/50 KDWS about 8 years ago. I went back up to factory diameter when the 4.56s went in. I may have to revisit the 50.
  6. Replies
    18
    Views
    3,253

    Tires: has it come to this?

    Hey all,

    It's that time again, time for new tires. Due to tie rod ends being toast, I ended up needing new front tires to pass inspection. No problem, I think. I have Federal 255/55's on all four...
  7. Replies
    23
    Views
    3,925

    If he went to a 26" slick could that be forcing...

    If he went to a 26" slick could that be forcing him to shift into OD before hitting the traps? That'll cost a couple tenths right there.

    Just a thought.
  8. Thread: 408 Idle Surge

    by Miggity
    Replies
    12
    Views
    2,707

    You guys may be on to something. :jester:

    You guys may be on to something. :jester:
  9. Thread: 408 Idle Surge

    by Miggity
    Replies
    12
    Views
    2,707

    Hadn't done this since the new motor went...

    Hadn't done this since the new motor went together. I set the IAC counts over the weekend and it stopped for a couple of days after I reset the counts. I was all set to post "RICH COMES THROUGH...
  10. Thread: 408 Idle Surge

    by Miggity
    Replies
    12
    Views
    2,707

    Just fixed them :biggthumpup:

    Just fixed them :biggthumpup:
  11. Thread: 408 Idle Surge

    by Miggity
    Replies
    12
    Views
    2,707

    I thought this also so I flashed it back to the...

    I thought this also so I flashed it back to the stock tune (MP PCM) and the issue didn't go away. Is there something I should be alerting Hemifever to look for?
  12. Thread: 408 Idle Surge

    by Miggity
    Replies
    12
    Views
    2,707

    408 Idle Surge

    Hey all,
    I still have that pesky surging idle. It's been around since the 408 went in. Here are the specs on the motor:



    The surge is at its worst when it's either above 80 degrees outside or...
  13. Thread: Plasti-Dip

    by Miggity
    Replies
    20
    Views
    7,877

    This is from the local truck club forum. Those...

    This is from the local truck club forum. Those wheels never saw the road. I guess your experience speaks volumes about the product Zoop is selling.
  14. Thread: Plasti-Dip

    by Miggity
    Replies
    20
    Views
    7,877

    This statement is true.

    This statement is true.
  15. Thread: Dyno Vid

    by Miggity
    Replies
    10
    Views
    2,996

    Here's the current setup: MP Cast stroker crank...

    Here's the current setup:
    MP Cast stroker crank
    Ross 9:1 Forged pistons
    factory rods
    Custom Grind Comp cam: 220/230 dur .544/.544 lift at 110 lsa
    clevite bearings, ARP hardware, ARP head studs...
  16. Thread: Dyno Vid

    by Miggity
    Replies
    10
    Views
    2,996

    It put down 309hp and 344lb/ft. Last run before...

    It put down 309hp and 344lb/ft. Last run before the newest tune it did 294hp. Now I just need to address this stock heads issue. :)
  17. Thread: Dyno Vid

    by Miggity
    Replies
    10
    Views
    2,996

    Dyno Vid

    Visited a Dyno Day down in Va Beach. Saw some improvement with a new tune. :)

    34pQ_LXP6jE
  18. Replies
    27
    Views
    5,102

    Anyone have a part number for the Remflex gaskets?

    Anyone have a part number for the Remflex gaskets?
  19. Replies
    27
    Views
    5,102

    Dead Horse: Leaky Spintech Headers

    Time to beat this dead horse again. :)

    What are people doing to get these things to seal up at the head? I know a lot of guys are running the one piece port plate. What about gaskets? I followed...
  20. Replies
    3
    Views
    1,739

    If you want to keep it relatively close to stock...

    If you want to keep it relatively close to stock diamter, Nitto makes a 275/50 that is a pretty good tire. They used to be pretty inexpensive, but the price went up recently. I'm running the Federals...
  21. Replies
    11
    Views
    3,489

    I tossed my factory shroud. Got a windshield...

    I tossed my factory shroud. Got a windshield washer reservoir from a boneyard out of a 99 Dak. Bought a universal coolant overflow canister from carquest. Came with brackets and everything. It's...
  22. What he said. I pulled my heads last year. It...

    What he said. I pulled my heads last year. It wasn't that bad. What I found under the heads was, though.
  23. Thread: iPhone App

    by Miggity
    Replies
    10
    Views
    3,329

    I like tapatalk because it will notify you when...

    I like tapatalk because it will notify you when someone replies to a thread you've posted in or you get a PM. Since I don't have my emails routing to my phone, this is handy. Tapatalk also works with...
  24. Thread: Black Paint

    by Miggity
    Replies
    22
    Views
    9,297

    For a while, Chrysler was helping some customers...

    For a while, Chrysler was helping some customers foot the bill for paint jobs paying for as much as half the total cost. Customers had to call Chrysler and put in a request and they would hear back...
  25. Thread: update

    by Miggity
    Replies
    17
    Views
    3,583

    Not sure how it is where you are, but in Va you...

    Not sure how it is where you are, but in Va you can take it somewhere else even after it's rejected. If it passes at another shop, all is well.
Results 1 to 25 of 269
Page 1 of 11 1 2 3 4