Search:

Type: Posts; User: ShelDak

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Thread: Pie

    by ShelDak
    Replies
    10
    Views
    1,894

    Was looking at their PIE EQ heads......

    Was looking at their PIE EQ heads...
    https://www.performanceinjectionequipment.com/mopar-eq-cylinder-heads

    270 flow at .550 lift. Looks like a decent deal. Upgraded springs etc.

    I'm back in...
  2. Replies
    1
    Views
    6,838

    Hughes Rollers Rockers and Pushrods

    Hughes 1.65 Roller Rockers (HUGH 1550), Edelbrock guide plates and CompCams 7634 Pushrods (5/16" diameter and 6.95" length). These were mocked up, not run. Complete.

    $275 - shipping to lower 48...
  3. Fluid level is fine. It's not burnt or stinky. ...

    Fluid level is fine. It's not burnt or stinky. Thinking one of the solenoids is bad - not sure they were replaced with the rebuild.
  4. Think I cooked the trans...which scanner reads the TCM?

    Well - technically it was my son, but now the "rebuilt" 46 RE is slipping. My Konnwei scanner doesn't see the TCM. I see two codes I can't read. I assume those are the trans codes. Which scanner...
  5. Replies
    29
    Views
    20,504

    There's another cheap R/T listed in St. Louis:...

    There's another cheap R/T listed in St. Louis:
    https://stlouis.craigslist.org/cto/d/03-dodge-dakota-rt/6679142294.html
  6. Thread: It is ALIVE!!!

    by ShelDak
    Replies
    5
    Views
    5,778

    Truck keeps running better and better. My wife...

    Truck keeps running better and better. My wife is upset about the multiple tire marks in the driveway. It's deadly from a roll @ 25 mph. Still needs some tuning, but wow.
  7. Replies
    29
    Views
    20,504

    Looks great - kicking myself about missing that...

    Looks great - kicking myself about missing that one. I live in NOCO, but work downtown. Looks great with new paint! Nice find!
  8. Thread: It is ALIVE!!!

    by ShelDak
    Replies
    5
    Views
    5,778

    Yes and yes! I have the edelbrock guide...

    Yes and yes! I have the edelbrock guide plates...stock block deck height and "stock" (not shaved) heads! The guide plates are very thick. I will check those out. That's nut's BTW.
  9. Thread: It is ALIVE!!!

    by ShelDak
    Replies
    5
    Views
    5,778

    It is ALIVE!!!

    Well after much headache, the R/T is back on the road. To say the least this thing seriously hauls the mail!

    I estimate mid-high 12's with the new upgrades. I've never driven a car that's as...
  10. Just as a frame of reference... I have the...

    Just as a frame of reference...

    I have the KB107's and EQ heads. I also went with the Hipotek HPT220X 110 LSA.

    Had to go with the Cometic gaskets (0.051 compressed). I had originally measured...
  11. Thread: Cam Selection

    by ShelDak
    Replies
    22
    Views
    13,477

    Motor back in! Not fired yet. Flyin Ryan is...

    Motor back in! Not fired yet. Flyin Ryan is next on my list. Will fire this weekend. Had to order header gaskets.
  12. Replies
    14
    Views
    11,065

    I've got the Mid-length Spintechs and have the...

    I've got the Mid-length Spintechs and have the straight boots, no issues.
  13. Replies
    9
    Views
    7,352

    I just went through this yesterday with my Hughes...

    I just went through this yesterday with my Hughes 1550's. Have to use the guide plates otherwise they will move to funny angles on the valves. Mine got all wonky with a few spins of the motor...
  14. Replies
    36
    Views
    20,014

    So just an update - motor is back together and in...

    So just an update - motor is back together and in the truck. Had to order header and collector gaskets so should be fired up by the end of the weekend. Will need computer tune before it runs...
  15. Thread: Cam Selection

    by ShelDak
    Replies
    22
    Views
    13,477

    14973

    14973
  16. Replies
    36
    Views
    20,014

    ok - I think I'm correct now...14972

    ok - I think I'm correct now...14972
  17. Thread: Cam Selection

    by ShelDak
    Replies
    22
    Views
    13,477

    Motor is out - brandy new Eagle rods in there!

    Motor is out - brandy new Eagle rods in there!
  18. Thread: Cam Selection

    by ShelDak
    Replies
    22
    Views
    13,477

    I finally got the piston part number - they are...

    I finally got the piston part number - they are KB107. Those are a flat top with valve reliefs. KB website shows 10.9 to 1 with a 62 cc head.
  19. Replies
    36
    Views
    20,014

    Motor does have Eagle Rods...that's a nice find.

    Motor does have Eagle Rods...that's a nice find.
  20. Replies
    36
    Views
    20,014

    A few things on the 10.2 on pump gas: ...

    A few things on the 10.2 on pump gas:

    Hyperutectic pistons hold heat = better burn
    I am 5030 elevation
    Didn't knock when previously running

    Thoughts?
  21. Replies
    36
    Views
    20,014

    http://wallaceracing.com/dynamic-cr.php Bore...

    http://wallaceracing.com/dynamic-cr.php

    Bore in Inches: 4.030
    Stroke in Inches: 3.58
    Rod Length in Inches: 6.123
    Static Compression Ratio: 10.9 (:1)
    Inlet Valve Closes ABDC : 36°
    Boost...
  22. Thread: Cam Selection

    by ShelDak
    Replies
    22
    Views
    13,477

    Well I did go for the Hughes Roller Rockers -...

    Well I did go for the Hughes Roller Rockers - found a used set on ebay. They are 1.65 ratio, so cam specs are a little more aggressive on lift.

    Went with the HiPoTek HPT220XP Performance...
  23. Replies
    36
    Views
    20,014

    I have picked a few things since last post: ...

    I have picked a few things since last post:

    Went with the HiPotek .512/.512 cam, 220 and 230 at 0.050

    Got the new springs that match the cam - they are a single with Dampener and they don't...
  24. Thread: Cam Selection

    by ShelDak
    Replies
    22
    Views
    13,477

    Stock rockers are good until around .525 lift -...

    Stock rockers are good until around .525 lift - so no, you don't always need to replace the rockers. Adjustable rockers add how much power?
  25. Thread: Cam Selection

    by ShelDak
    Replies
    22
    Views
    13,477

    I don't know yet on the pistons. Motor isn't...

    I don't know yet on the pistons. Motor isn't quite out. Was going to measure everything when it's apart. Hoping I don't find anything else wonky.

    Looking like I'm at least 10+ to 1, maybe...
Results 1 to 25 of 74
Page 1 of 3 1 2 3