Search:

Type: Posts; User: Filthy Filbert

Page 1 of 20 1 2 3 4

Search: Search took 0.09 seconds.

  1. Thread: nv3500

    by Filthy Filbert
    Replies
    22
    Views
    1,412

    Keep in mind yours uses the old nv4500 cast...

    Keep in mind yours uses the old nv4500 cast aluminum bell that’s cut and welded up to fit a T56. More than one person has had to get them completely reworked due to cracking. Also, good luck...
  2. Thread: nv3500

    by Filthy Filbert
    Replies
    22
    Views
    1,412

    Also, all the cross members were the same...

    Also, all the cross members were the same regardless of auto/stick
  3. Thread: nv3500

    by Filthy Filbert
    Replies
    22
    Views
    1,412

    Yup. And the master cylinder. T56 needs:...

    Yup. And the master cylinder.

    T56 needs:
    QuickTime bell
    Custom 130 tooth flywheel
    10.5 or 10.95” 26-spline clutch
    Viper hyd TO bearing
    Fittings and -3an hose to connect viper TO to dakota...
  4. Thread: nv3500

    by Filthy Filbert
    Replies
    22
    Views
    1,412

    I had a nv3500 originally. Never had a problem...

    I had a nv3500 originally. Never had a problem with exhaust figment. That was with edelbrock mids and Mopar Pph.

    Bell is cast into the transmission case. It’s all one piece. Even if it was...
  5. Sticky: Cool. You seem to know what you’re doing....

    Cool.

    You seem to know what you’re doing. Don’t call the guy who builds custom flywheels or clutches.

    Have fun.
  6. Sticky: Why are you reinventing the wheel? All that...

    Why are you reinventing the wheel? All that work has already been done. Call Gerko enterprises and order a flywheel. Talk to him about clutches because he’s also a clutch expert and the sole US...
  7. Thread: Dakrt56

    by Filthy Filbert
    Replies
    90
    Views
    12,245

    Hope someone took the time to figure out the...

    Hope someone took the time to figure out the alloy to choose the right filler and process before blasting away at it. Those pieces are typically made out of hardened tool steel and welding on it can...
  8. Thread: Dakrt56

    by Filthy Filbert
    Replies
    90
    Views
    12,245

    I have a few shifters laying around oem viper...

    I have a few shifters laying around oem viper and I think a spare front location shifter.

    Pm me if you need one for parts
  9. Sticky: Yup

    Yup
  10. Nope There’s a reason that 15” wheels were no...

    Nope

    There’s a reason that 15” wheels were no longer an option starting in 2003
  11. Replies
    16
    Views
    2,804

    The stock wheels are such a horrible design for...

    The stock wheels are such a horrible design for brake clearance, I can almost guarantee you won’t get a 14” set-up to fit. But, I don’t have a 17” wheel to test with.
  12. Replies
    11
    Views
    1,243

    9.25 is stout. Do what Dave did

    9.25 is stout. Do what Dave did
  13. 140 seems ok. If you were down at 100, or had 1...

    140 seems ok. If you were down at 100, or had 1 cylinder low, you would do the leak down to find out where it’s going. A rudimentary way to do one is to just put shop air to the cylinder to hear...
  14. Normal. The spindle is cast iron. The pads...

    Normal. The spindle is cast iron. The pads are steel backed. Wear is going to happen. Need to file the spindle till its flat again.

    Or buy one of my brake kits and run fixed Brembo calipers.
  15. Placement isn't that critical. Anywhere the...

    Placement isn't that critical. Anywhere the sensor is in water is all you need
  16. Replies
    4
    Views
    356

    Last time I saw it it was. I'll take a look at...

    Last time I saw it it was. I'll take a look at it my next time out there.
  17. Replies
    4
    Views
    356

    I have one in storage but it's got some rust on...

    I have one in storage but it's got some rust on it.
  18. FYI... crank at 12, cam at 6 with the dots... ...

    FYI... crank at 12, cam at 6 with the dots... is TDC, firing on #6

    Both dots at 12 is TDC, firing #1.

    This is why so many distributors get installed 180 degrees off and engines don't start
  19. I've never had a new hub assembly NOT come with a...

    I've never had a new hub assembly NOT come with a new nut. no need to buy new ones separately. Keep your receipt in case you decide to return them.
  20. Why do you want to remove it? What will you put...

    Why do you want to remove it? What will you put in the hole after you remove the sensor? What's wrong with just leaving the sensor there, unplugged and not hooked up to anything?
  21. Uh, reservoir size/shape/location is completely...

    Uh, reservoir size/shape/location is completely irrelevant to its function.
  22. They used to be different from year to year, but...

    They used to be different from year to year, but the parts suppliers have apparently decided to stock the 03/04 master for all 97-04 Dakotas, because it's cheaper to make 1 vs 2 different types of...
  23. Congratulations to your new DRTC President!! Kevin "GoFastGray" Peacock!!

    Members, Chase has conceded after seeing the lead that Kevin had in the election, so I am announcing that Kevin Peacock is your new club president. I will help him out in anyway possible and...
  24. Replies
    39
    Views
    2,648

    I will post up the polls at the end of this week....

    I will post up the polls at the end of this week. So far, we have Kevin "GoFastGrey" who has accepted, and Chase "Chase1500" who has accepted. Any additional nominations you want to make, or...
  25. Pulling the engine and cleaning the firewall...

    Pulling the engine and cleaning the firewall won't hurt the engine. It'll run the same as before when you put it back in. It's 8 hours of work to pull and reinstall the engine. You could start...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4