Search:

Type: Posts; User: niebs

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Thread: Turbo Oil supply

    by niebs
    Replies
    4
    Views
    80

    Thanks for the tip on the vortex install. that...

    Thanks for the tip on the vortex install. that does not seem like a bad way to go.
  2. Thread: 9.6 @ 143mph

    by niebs
    Replies
    13
    Views
    362

    TexasSpeed has good cams. Damn someone just had...

    TexasSpeed has good cams. Damn someone just had half off ls cams too. Ill try to remember who it was.
  3. Thread: Turbo Oil supply

    by niebs
    Replies
    4
    Views
    80

    is there not any free ports in the block? Maybe I...

    is there not any free ports in the block? Maybe I could add a Tee where the pressure sending unit goes.
  4. Thread: Turbo Oil supply

    by niebs
    Replies
    4
    Views
    80

    Turbo Oil supply

    Where are you turbo guys getting your oil supply from? (single turbo, right side of engine bay)
    and might as well ask, where are you draining it to?
  5. Same to you good buddy! \:drtc_logo001: Everyone...

    Same to you good buddy! \:drtc_logo001:
    Everyone be safe out on the roads. Lots of crazies out there.
  6. Replies
    19
    Views
    550

    :roflmao::roflmao:

    :roflmao::roflmao:
  7. Replies
    19
    Views
    550

    Is it still n/a if it runs on cocaine? :jester:

    Is it still n/a if it runs on cocaine?
    :jester:
  8. Thread: 9.6 @ 143mph

    by niebs
    Replies
    13
    Views
    362

    no matter the power plant. These chassis on the...

    no matter the power plant. These chassis on the strip is a good thing!
  9. Thread: 9.6 @ 143mph

    by niebs
    Replies
    13
    Views
    362

    Good stuff! they take some power.

    Good stuff! they take some power.
  10. Thread: 9.6 @ 143mph

    by niebs
    Replies
    13
    Views
    362

    Turn it up! What block, heads and turbo size?

    Turn it up!
    What block, heads and turbo size?
  11. Replies
    98
    Views
    12,208

    Are you running solid lifters?

    Are you running solid lifters?
  12. Thread: 99 Dakota Build

    by niebs
    Replies
    4
    Views
    336

    :biggthumpup: are you running the ms3x as stand...

    :biggthumpup:
    are you running the ms3x as stand alone or parallel? what trans?
  13. Replies
    4
    Views
    336

    Clear coat. I need to do mine as well. It's...

    Clear coat. I need to do mine as well. It's freaking brutal!
  14. Thread: Mopar

    by niebs
    Replies
    6
    Views
    198

    Why would you buy that? 25k will buy you a hell...

    Why would you buy that? 25k will buy you a hell of a lot more then 850hp.

    Lots of hemis in the junk yards now a days. Heads flow insane amount as is.
    I just need to decide on a trans for mine.
  15. Thread: Mopar

    by niebs
    Replies
    6
    Views
    198

    supply and demand. Mopar ppl is a small group....

    supply and demand. Mopar ppl is a small group. Switch to a hemi. still mopar and is cheaper to make power.
  16. Thread: Rims for slicks

    by niebs
    Replies
    16
    Views
    555

    You should put together a build thread or...

    You should put together a build thread or something. I would like to hear more about your combo and pics of your truck. Sounds wicked!
  17. Replies
    7
    Views
    257

    e85 on low compression is not worth it imo. If...

    e85 on low compression is not worth it imo. If you plan on FI then i would say look into it. You will basically need to replace the whole fuel system and then have a way to tune for the fuel.
  18. Thread: Rims for slicks

    by niebs
    Replies
    16
    Views
    555

    1000+ hp on a 360 mag block?

    1000+ hp on a 360 mag block?
  19. Thread: Rims for slicks

    by niebs
    Replies
    16
    Views
    555

    Goals? 9.25 seem to hold up to a good amount of...

    Goals? 9.25 seem to hold up to a good amount of abuse.
  20. If that was towards me then, its going to start...

    If that was towards me then, its going to start as a early 5.7 block. stockish cub. 11:1 compression carbd, 7500rpm, nitrous motor, controlled with holley hp cause thats what parts i have currently....
  21. :biggthumpup: https://i.imgur.com/GwQ6gFX.jpg

    :biggthumpup:


    https://i.imgur.com/GwQ6gFX.jpg
  22. Replies
    0
    Views
    140

    ECM trans interchange

    Quick question. Would a stock tune 01 ecm from a 4x4 46re work on a 01 2wd 42re?
  23. :biggthumpup: Awesome man! Any solid mounts?

    :biggthumpup: Awesome man!

    Any solid mounts?
  24. Replies
    16
    Views
    777

    IS there a reason you used 03-04 spindles?

    IS there a reason you used 03-04 spindles?
  25. Replies
    16
    Views
    777

    Isnt there a work around with crown vic hubs or...

    Isnt there a work around with crown vic hubs or something?
    I would just look into using mustang struts.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4