Search:

Type: Posts; User: arro222

Page 1 of 20 1 2 3 4

Search: Search took 0.12 seconds.

  1. Thread: Misfire in #7

    by arro222
    Replies
    7
    Views
    285

    It may be cheaper or at least a similar cost to...

    It may be cheaper or at least a similar cost to have another junk yard 360 installed and put whatever parts you have on the original on the replacement. It'll probably be faster as well. An engine...
  2. Thread: Misfire in #7

    by arro222
    Replies
    7
    Views
    285

    If you're burning oil, you have a ring problem....

    If you're burning oil, you have a ring problem. Squirt some oil into that cylinder and see if your compression goes up. The oil will act as a temporary seal. If it does go up and then down, it is...
  3. Just some added info. I believe the gasket you're...

    Just some added info. I believe the gasket you're looking to get is a composite rubber/steel affair. I don't like the all rubber ones for pan gaskets unless they're real good. The pure rubber ones...
  4. Replies
    8
    Views
    263

    Cheez. It's like being Rip Van Winkle..

    Cheez. It's like being Rip Van Winkle..
  5. Replies
    8
    Views
    263

    That makes sense. Who am I kidding. None of this...

    That makes sense. Who am I kidding. None of this electronic stuff makes sense to me.
    I gotta snag an ibm laptop someplace and get in touch with Ryan.

    What I still cannot understand is how the...
  6. Replies
    8
    Views
    263

    No, truck is not tuned. Thought it was running...

    No, truck is not tuned. Thought it was running pretty good without it which surprises me as I thought after you do all the top end stuff, it would hardly run at all w/o a tune. It normally reads...
  7. Replies
    8
    Views
    263

    wide band reading at lock up

    Not ever having an automatic performance wise vehicle, why is it my wide band shows an 11 at torque converter lock up when truck is floored? Normally fluctuates between 12-12.5 until the converter...
  8. They are. Check into if this gasket needs to be...

    They are. Check into if this gasket needs to be torqued differently inch pound wise.
  9. There are 3 kinds of gaskets for this. Rubber,...

    There are 3 kinds of gaskets for this. Rubber, fiber and cork. I like the rubber type mainly because they are reusable. Cork has been used for ages and is an effective gasket. Fiber gaskets are...
  10. I like their "third hand" gasket allowing you to...

    I like their "third hand" gasket allowing you to put up some bolts into the pan for easier cinching and alignment.
  11. Saying the pan had the same shape integrity that...

    Saying the pan had the same shape integrity that you came in with, these need to be tightened to about 8 ft pounds only. You should need no other sealant.
  12. Replies
    26
    Views
    444

    I think any head would use more work for racing....

    I think any head would use more work for racing. They'd probably be closer to $4K or over with racing in mind depending on porting and materials. If what they say is true, the flow numbers as they...
  13. Replies
    26
    Views
    444

    I don't think so either. May have worded my...

    I don't think so either. May have worded my statement incorrectly to give the impression that I thought the price was high. Should have said "a legitimate price". That they flow as high as they do...
  14. Replies
    26
    Views
    444

    Which is more than a legitimate price in my mind...

    Which is more than a legitimate price in my mind for a complete cnc head made out of aluminum. It would be nice if they had flow rates printed somewhere.
  15. Replies
    26
    Views
    444

    It stipulates in the copy to use the HS stuff for...

    It stipulates in the copy to use the HS stuff for magnums on these heads.
  16. Replies
    26
    Views
    444

    Good to have someone else in the game with fresh...

    Good to have someone else in the game with fresh tooling.
  17. Replies
    20
    Views
    378

    A historic member. Good stuff. Welcome back.

    A historic member. Good stuff. Welcome back.
  18. Replies
    16
    Views
    556

    I go back to that "while" neibs. It was the dawn...

    I go back to that "while" neibs. It was the dawn of drag racing. I was going to say "as we know it now" but that would be a bastardization. What it was and what it is now as far as the ultimate...
  19. Replies
    16
    Views
    556

    It is about compound as well as sidewall...

    It is about compound as well as sidewall construction. Street tires simply get "glazed" over when heated too much and become "greasy" rather than sticky. Tracks are stickier than the street so take...
  20. Replies
    16
    Views
    556

    Driving being equal, he'll win. He has a better...

    Driving being equal, he'll win. He has a better power to weight ratio. I mean look at the torque rating on his truck. Traction will be king. Driving quality will make the difference. I've beaten...
  21. Replies
    5
    Views
    278

    If you're in the business, it's important to have...

    If you're in the business, it's important to have all the right stuff. At least in can be paid for.
  22. Replies
    13
    Views
    451

    That would be $300 if it was a Snap-On.

    That would be $300 if it was a Snap-On.
  23. Replies
    4
    Views
    270

    You have a better memory than me Syn. Right...

    You have a better memory than me Syn. Right niebs. I realize rates for work vary upon region. A clue to what you're getting for your money may just be where the company is. California, as with most...
  24. Replies
    4
    Views
    270

    careful about heads from this company

    Because of almost a majority of peeps stating IMM Engines in Cali was a good company to deal with, I went ahead and ordered a set of slightly warmed over heads from them. Someone here (I forget who)...
  25. Replies
    91
    Views
    10,038

    Do a compression check to make sure your valves...

    Do a compression check to make sure your valves are fully closing. How may turns at the rockers? Could be too tight. 1 and a half was all I could do even though two was recommended.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4