Search:

Type: Posts; User: JDreamR/T

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds; generated 3 minute(s) ago.

  1. Doing my best Jim, also trying to keep things as...

    Doing my best Jim, also trying to keep things as economical as possible. It recently occured to me that the front dakota rotor may just work out, however the rotor hat offset is deeper so the caliper...
  2. Hi everyone, I just wanted to drop in to say the...

    Hi everyone, I just wanted to drop in to say the past year has been a great pleasure selling these rear disc conversion kits. Happy to report I've shipped 20 orders to date since inception of...
  3. Thread: Found this

    by JDreamR/T
    Replies
    16
    Views
    1,726

    I'd really love to check out Island Dragway,...

    I'd really love to check out Island Dragway, never been. Also never made it to Atco, always just assumed I'd make it there eventually someday, what a shame they closed down. Also, my truck has never...
  4. Replies
    32
    Views
    10,340

    Hi Mike, just chiming in here, no need to remove...

    Hi Mike, just chiming in here, no need to remove spindles for powder coat, easy to mask or sometimes coaters will just vacuum the powder from the areas they want uncoated.
    When upgrading the...
  5. Replies
    7
    Views
    4,281

    I second what Jim said, huge collection of over...

    I second what Jim said, huge collection of over 3,100 Mopars apparently. I was excited to make the trip and finally take the R/T for it's first extended cruise since being rebuilt. Happy it ran...
  6. First set of calipers finished in gloss black for...

    First set of calipers finished in gloss black for evilrt! Love how they turned out, looking forward to shipping these kits out finally!

    https://i.imgur.com/WLGJHir.jpg
    ...
  7. Replies
    8
    Views
    1,260

    Hmm yeah I can see that causing resonance if the...

    Hmm yeah I can see that causing resonance if the rack is loose or a broken tooth, the wheel would vibrate a bit too I would think. Could be tie rods, inner or outer...that's about all I got lol. Good...
  8. Replies
    8
    Views
    1,260

    Stupid question but possibly the plastic fender...

    Stupid question but possibly the plastic fender liner popped out just a bit and contacts the corner of the tire on turns? :idunno:
  9. :biggthumpup: Thank you everyone again for the...

    :biggthumpup:

    Thank you everyone again for the support. The first 10 slots for orders have been filled. Stick around for news on future runs of these kits. Feel free to message me for further...
  10. Rear Disc Conversion Kit for Dakota R/T's...

    Rear Disc Conversion Kit for Dakota R/T's (1998-2002) - 9.25 Axle, 13" Vented Disc!
    *please read the following carefully*
    Happy to officially announce my offering of this setup of the '15+ Mustang...
  11. Canadian_RT appreciate it budd'eh!. Feel free to...

    Canadian_RT appreciate it budd'eh!. Feel free to reach out whenever that day comes, I'd be happy to help you out!


    Awesome, thanks for the interest!


    100% agree. Tremec swapped myself, so I...
  12. Fixed :drtc_logo001::biggthumpup: All good,...

    Fixed :drtc_logo001::biggthumpup:


    All good, got to keep this forum alive long live the :drtc_logo001:


    Thanks Rich, and appreciate all the support from everyone. I should be posting prices...
  13. New year update!

    Happy New Year everyone, a little new year's update - happy to say I've logged a couple thousand miles now on the truck since installing these brakes back in April '22. I'm happy to report that the...
  14. Yup, yup! The fronts worked out really nice!...

    Yup, yup! The fronts worked out really nice! Turns out they only needed a spacer to center the caliper over the rotor. Otherwise they are pretty much a bolt-on setup to the 03/04 knuckles. From there...
  15. Replies
    11
    Views
    2,028

    :rockwoot::biggthumpup: Excited to hear how it...

    :rockwoot::biggthumpup: Excited to hear how it all goes! Happy New Year Richard!
  16. Replies
    11
    Views
    2,028

    Very cool stuff Richard, looking good! I also am...

    Very cool stuff Richard, looking good! I also am curious to see how the setup all checks out. What are your goals/plans for these heads?
  17. Replies
    8,427
    Views
    2,269,928

    Took the truck out of the garage today, drove...

    Took the truck out of the garage today, drove around the block for a bit to stir up the fluids etc,,,still drives good and strong :drive:

    then noticed some coolant weeping from the water pump...
  18. Replies
    13
    Views
    2,309

    Very nice, 3 years in the making way to stick it...

    Very nice, 3 years in the making way to stick it out! :r/t smile:
  19. Replies
    2
    Views
    7,134

    I have this seal if you want it, never used

    I have this seal if you want it, never used
  20. There is a sticky here for qa1 part numbers...

    There is a sticky here for qa1 part numbers http://www.dakotart.com/forum/showthread.php?23227-QA-1-info-amp-new-part-numbers

    But ultimately depends on your drop so measuring from the upper and...
  21. Replies
    11
    Views
    1,278

    Could be a crank sensor, my uncle has a Dodge...

    Could be a crank sensor, my uncle has a Dodge 1500 who chased similar issues after replacing multiple ignition parts, grounds etc. Turned out to be that.
  22. Received my laser cut brackets and did a little...

    Received my laser cut brackets and did a little mockup, looks really good! Had to do a touch of grinding on the over-the-axle radius, but otherwise a perfect fit and the pads line up perfectly on the...
  23. Thanks, you are correct it was considerably more...

    Thanks, you are correct it was considerably more to have a CNC bracket made. My first design was a 1 piece billet part, and the quotes I got back were cost prohibitive. The two piece bracket design...
  24. nitroram33 thanks for sharing your method,...

    nitroram33 thanks for sharing your method, definitely a nice way to go for a 5 lug conversion! Nicely done!

    So I have some updates. I finished the preliminary design for the rear disc conversion...
  25. Replies
    10
    Views
    1,776

    Lol. But where's the fun in that?

    Lol. But where's the fun in that?
Results 1 to 25 of 498
Page 1 of 20 1 2 3 4