Glad its back!
Type: Posts; User: thomasfouraker
Glad its back!
Anyone tuned their own truck with HP Tuners, or had theirs tuned by a tuner that used HP Tuners?
I would like to ask some questions and maybe look at some of your data logs and tune files to make...
It was suggested to me by a local tuner that 42lb Fords should be good as they should net actually higher on the Dodge higher PSI fuel system. He said they would also cover me under moderate boost...
I guess hitting 110% isn't good then!
My friend told me the only way to know you need bigger injectors is to first rule out the fuel pump. The injector will up its duty cycle to meet the demand...
Wanted to give an update on where I am at.
Definitely found the power with some basic tuning corrections. Without going into boring detail I was flooding my cylinders at lower vacuum and getting...
Sold
Yea, the right stuff, not great stuff. ha ha I knew it was something like that!
I don't care for the china wall gaskets. Some "Great Stuff" is better IMO.
Those rubber gaskets are ok if you are running all factory, non machined components, but I wouldn't trust them to be...
161441614516146161471614816149
Found about 8 roller tips with some form of defect in them. I wouldn’t hesitate to run them after inspecting them closer. Might would polish them with some 3000 and...
HPTuners MPVI2 interfaced with AEM wideband through serial output to the software.
We are going to get the fuel tables friendly over a few days. He has a draggy which will help gather performance...
SOLD
Have a set of new unused (mocked up) 1.7 roller rockers I was going to use I purchased very early in my build.
The build grew and I ended up getting a custom camshaft ground for 1.6...
Better than I remember it!
I appreciate the reply.
Never heard that about the snap on scanners. Seems odd that it would read backwards. I will try to get it to 0. I imagine that clockwise would advance and counter...
I don't think so Mike. I had to borrow an MT2500 to set mine. When I placed my distributor in, I set the #1 at TDC on the compression stroke, dropped the oil pump gear in and set it at the...
Appreciate all the feedback. Going to get the exhaust straightened out and hope to order an HPtuners this following week. I have a friend that tunes his twin turbo LS no prep car and he told me I...
What piston dish do you have and what is your deck to piston clearance?
Heads are already 58.5-59cc. I cc’d them before ordering head gaskets.
Would have to get a different timing set, my pro...
16121
Maybe this will be a better picture
1611916120
I am not a cam wizard (obviously) but would either of these be worth swapping into the motor prior to getting the tune?
On hand I have two camshafts that I could potentially swap out and run. I will track down the cam cards and post them up to see if either would be more favorable.
Thanks Richard,
Kinda aggravating because I called Comp and gave them all the information and this is what they specd. I even called them back and told them I wanted to go a bit smaller but was...
Valve train is the factory stamped 1.6 rockers with preload to 21ft/lbs. per factory spec.
I checked compression 175-185 on all 8. I think my gauge also reads about 15lbs low when I tested it with...
No tune to speak of. I ran it up and down the road a bit on the factory tune, then I came back and uploaded the 91 octane flashpaq tune from my old Superchips tuner I used for my tire size.
...
16118
Hopefully the picture attached. Not that good with the phone.
Degreed the cam in with a nice big degree wheel. It wasn’t ground with advanced but I did set the timing gears at 3 degrees...
Okay guys here goes......
Just finished putting together what I hoped was going to be a torque monster, between speaking to Hughes, Comp, and a few engine builders this should have been making...
You never know, I purchased a set of Mopar Performance RT heads, PPH Headers, roller rockers and a FB Throttle body in 2020, from a thread in 2012.