thanks, but thats exactly how i ended up with this cam...
Type: Posts; User: edb2007
thanks, but thats exactly how i ended up with this cam...
this will only work in the older 318/340/360 LA motors. the cam would bolt in, but it isnt correct for your dakota.
Yes, LA motor and comes with new hydraulic flat tappets.
I have been accumulating some mopar performance parts that i cannot use and i figured i would post them here to see if anyone wants them.
first is a P4120233 mopar purple camshaft. advertized...
yep, master tech at dodge store shouldnt modify his own truck.
two threads about putting them into 318nv3500 trucks, close to nothing about automatics.
its been said more than once the "hack"...
"I guarantee you that this fresh T-56 is nicer than anyone you are getting locally" said patrick, before i bought the transmission. i would hope that written guarantee would come with the money to...
yeah mines got a bleeder on the slave, it wouldnt work correctly at first but a few pushes of the pedal and it seemed to be working alright. still going to bleed it today at work. still gotta hook up...
got the yoke to the driveshaft shop and they made me a new driveshaft with new u joints and all. i got home and put it in and she moved under her own power! but im having problems bleeding the clutch...
thatll do... THANKS! :D
so pin 1 and 3 to the reverse light switch, and pin 2 to ground... solunds good.
driveshaft is discontinued through mopar, and it was 600 bucks. i was going to order the...
Edb2007@hotmail.com
anyone know what diveshaft should be used or how to hook up my reverse lights?? anyone? anyone?
im thinking if i can get a slip yoke that fits the t56 and have it attached to my driveshaft.
...
So stock rc Dakota 318 5speed driveshaft will work if your putting it into an automatic?
or is it a stock rc ram 318 2wd?
My rc dakota 360 auto driveshaft is 30 splines but slightly short and does...
the three prong connector that is right under the rear solenoid looks like it is the output shaft speed sensor. weird because my output shaft sensor is only 2 wires....
i threw the transmission up there and bolted it up. jacked it up high enough to make a high spot. let it down enough to cut a 4" hole a half inch forward of the high spot, to allow for forward...
the crankshaft sensor itself is like 100 bucks. it was about a mm away from the flexplate so i mounted it about a mm away from the flywheel. i do not know the exact measurement, but if it works itll...
once i got the crankshaft position sensor shimmed away from the flywheel, i installed the quicktime bellhousing and starter.
http://i106.photobucket.com/albums/m260/edb2007/photo.jpg
when the...
TRANSMISSION DRAIN AND FILL PROCEDURE
The lubricant recommended for the T-56 transmission is MoparŪ Synthetic Manual Trans Lubricant 75W-85 (MS-9070) Any lubricant conforming to Material Standard...
that makes me curious, because i think i bought that trans. its got the same sticker, but mopar does not reccomend atf. does anybody know the history of this trans? did sombody modify it to take only...
i was doing some research on the pedal swap and i noticed #4 is the same part in both the automatics and the manuals. so it appears all i will need to do is switch the pin and the parts attched to...
The lubricant recommended for the T-56 transmission is MoparŪ Synthetic Manual Trans Lubricant 75W-85 (MS-9070) Any lubricant conforming to Material Standard MS-9070 is acceptable for use.
The...
I have everything except the tune.
http://i106.photobucket.com/albums/m260/edb2007/IMG_0770.jpg
as you can see the flex plate bolts are too small and i got some longer ones.
:drive:
parts list
viper spec t56
reverse lockout solenoid
lockout solenoid wiring
quicktime bellhousing
custom 130 tooth flywheel
6 longer flywheel bolts
new pilot bearing
Well thanks for all info everyone! I'm putting the transmission back in today.
13k ago i had my transmission overhauled with new clutches, steels, seals and orings(moparts). the transmission failed because of the 2nd gear band,so i upgraded the 2nd gear band and added a 4.2...