Search:

Type: Posts; User: 99dart

Page 1 of 20 1 2 3 4

Search: Search took 1.17 seconds.

  1. Replies
    4
    Views
    3,617

    Well... This from an old fart that would rather...

    Well... This from an old fart that would rather drive mine than have it sit for years. I'd build your engine. Bored 360 or 408 will be quicker and less hassle in the long run. My 365 with 10.6 to 1...
  2. Replies
    2
    Views
    750

    I cut my hood about the same as you have marked....

    I cut my hood about the same as you have marked. I made a radius type cut at the back edge for my round air filter. I'll try to take a picture of it later for you. I haven't had any issues with flex.
  3. Replies
    23
    Views
    4,841

    Ram's use a clamp around the TB, right? That...

    Ram's use a clamp around the TB, right? That would be one way. I replaced one of the a/c bracket bolts with a stud to help secure my big fresh air fiberglass housing that fits up tight to the hood. I...
  4. Replies
    23
    Views
    4,841

    Sounds interesting. My thought process went to...

    Sounds interesting. My thought process went to making it a slide-in assembly. Kind of like you slide a furnace filter into place.
  5. I say NO. We are an R/T specific site (as lame as...

    I say NO. We are an R/T specific site (as lame as it is now). This site is about the 1998-2003 Dakota R/T and what we do to personalize them. Yes, I am an OG. I've owned and thrashed on my R/T since...
  6. Thread: SCT tuner help

    by 99dart
    Replies
    19
    Views
    7,313

    Don't use hemifever... been there done that years...

    Don't use hemifever... been there done that years ago. Go with FRP. He is very busy, but the best at sct tunes.
  7. Replies
    4
    Views
    3,804

    Don't know about Mike. Haven't seen him on here.

    Don't know about Mike. Haven't seen him on here.
  8. Replies
    4
    Views
    3,804

    When I saw, "out with the old", I thought there...

    When I saw, "out with the old", I thought there goes the R/T! Glad you're still keeping her! I need some incentive to get down there and race! When would be a good time to meet you at the track,...
  9. Replies
    6
    Views
    2,008

    Alright! :biggthumpup: Glad you found some.

    Alright! :biggthumpup: Glad you found some.
  10. Replies
    143
    Views
    41,376

    Lookin' good, Richard! :r/t smile:

    Lookin' good, Richard! :r/t smile:
  11. Go figure... :dumbass234:

    Go figure... :dumbass234:
  12. Replies
    8,427
    Views
    2,269,982

    Wow, good to see you back, Duner!!

    Wow, good to see you back, Duner!!
  13. Replies
    3
    Views
    756

    Looking on Rock auto, a couple show bore dia of...

    Looking on Rock auto, a couple show bore dia of 1.125. Don't know if it makes a differece ornot. My converted my 99. Pedal felt hard until I got it out on the road stopping several times. Now it...
  14. Replies
    8
    Views
    1,260

    You got me... sounds kinda like a tire rub.

    You got me... sounds kinda like a tire rub.
  15. Replies
    8,427
    Views
    2,269,982

    Dunno why, but I haven't had any problem with...

    Dunno why, but I haven't had any problem with that connection. Still using the original tube AND O-ring! I have a rear main seal leak from over pressurizing internally. Lost a valve cover cap and...
  16. Replies
    7
    Views
    1,247

    New cap & rotor make a difference also. It should...

    New cap & rotor make a difference also. It should have a full tune up before drag racing...
  17. Replies
    103
    Views
    12,263

    Yes, sag can be adjusted. IIRC I had my lower...

    Yes, sag can be adjusted. IIRC I had my lower valance off so I could reach up in there. I had my bumper off for paint job. So get the bolts loosened up, then you can move/adjust the bumper.
  18. Replies
    7
    Views
    1,247

    Or, NGK bkr6E, bkr7E

    Or, NGK bkr6E, bkr7E
  19. Replies
    13
    Views
    2,309

    That's what I love about these fuel injected...

    That's what I love about these fuel injected engines. :rockwoot:
  20. Thread: Dragy vids

    by 99dart
    Replies
    6
    Views
    2,202

    So, what were the times? 1/4 mile, top speed?

    So, what were the times? 1/4 mile, top speed?
  21. Replies
    103
    Views
    12,263

    Looking good! Stay with it. You'll have it back...

    Looking good! Stay with it. You'll have it back to nice in no time...
  22. Thread: Lost and Found

    by 99dart
    Replies
    4
    Views
    1,570

    Hey, glad you found your old truck! Not sure, but...

    Hey, glad you found your old truck! Not sure, but I probably have your original trans in my r/t. Dan Bennett hooked me up with Don thinking it was a good trans. (wasn't). Now that I wrote that...I'll...
  23. Replies
    8
    Views
    2,197

    I'm just seeing this post. Dan Bennett (Danno)...

    I'm just seeing this post. Dan Bennett (Danno) was a leader in trying new to 1998-2004 ways to make more HP in these trucks. His 98 Club cab STOCK bottom end, massively ported 2.02 heads, big cam and...
  24. Replies
    14
    Views
    3,037

    "Had this setup when I bought the truck from...

    "Had this setup when I bought the truck from Alan. He had tried to it use both cables and keep the PRD21 working on the dash. Think it had some binding issues".
    When I installed my Ford Taurus SHO...
  25. Replies
    22
    Views
    3,355

    Are you talking about the O2 sensor for the AEM...

    Are you talking about the O2 sensor for the AEM gauge or factory O2 sensors in exhaust? NTK or Mopar sensors work best in exhaust. :) :r/t smile:
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4