Search:

Type: Posts; User: 98Dak408

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    9
    Views
    2,107

    That's a thought. But I'm not sure I have enough...

    That's a thought. But I'm not sure I have enough original axle width for the slightly wider stance I want. I also have to drop the axles about an inch lower for the front steering wheels to clear...
  2. Replies
    9
    Views
    2,107

    The wheels and tires came in. Will have to make...

    The wheels and tires came in. Will have to make new axles since the wheels require 5/8" OD and the wagon came with 1/2" OD axles. I may also kick the rear axle back about an inch or an...
  3. Replies
    9
    Views
    2,107

    Home Depot is shipping to my house for free. ...

    Home Depot is shipping to my house for free. https://www.homedepot.com/p/Gorilla-13-in-Pneumatic-Replacement-Tire-GCT-13-8/328568676
  4. Replies
    9
    Views
    2,107

    By the way, the Harbour Freight 13" pneumatic...

    By the way, the Harbour Freight 13" pneumatic tires/wheel are absolute garbage. One of my buddy's is a golf course superintendent and they replaced a number of pieces of equipment wheels with the...
  5. Replies
    9
    Views
    2,107

    Trying to find Gorilla cart 13" pneumatic tires...

    Trying to find Gorilla cart 13" pneumatic tires through mail order on-line proved fruitless. Everyone is trying to sell the flat free tires. I was surprised to find Lowes has them in stock for $25...
  6. Replies
    23
    Views
    4,841

    Thank you!

    Thank you!
  7. Replies
    23
    Views
    4,841

    Just received an extra filter element in the...

    Just received an extra filter element in the mail. Was skeptical that I would actually receive it. The air cleaner is a go as I can find the time to work on it.
  8. Replies
    9
    Views
    2,107

    I've decided to go with a larger 13" diameter...

    I've decided to go with a larger 13" diameter wheel/tire with ball bearings. The wagon currently has 9.5" tires and friction bearings without lubrication, so the heavier the cart is, the harder it...
  9. Replies
    17
    Views
    21,467

    With my new tool cart, I may try to pull some of...

    With my new tool cart, I may try to pull some of that stuff when I see it in the future, like the brakes, sway bars, etc.
  10. Replies
    143
    Views
    41,377

    As I get older, I cannot tolerate excessive drone...

    As I get older, I cannot tolerate excessive drone in the cab. Therefore, I want to try running a resonator in front of the muffler in hopes of reducing noise. The muffler change provides me with a...
  11. Replies
    143
    Views
    41,377

    I'm only selling the one set of bullet mufflers...

    I'm only selling the one set of bullet mufflers Mike. They were originally going on my '98 Dakota but I went a different route. Once that set of bullet mufflers sell, I won't be making more,...
  12. Replies
    23
    Views
    4,841

    I found out the other day that K&N discontinued...

    I found out the other day that K&N discontinued the Viper panel air filter that I plan to use. K&N told me they had a lot of products discontinued in 2023. Probably not selling enough of them with...
  13. Sounds good! :biggthumpup:

    Sounds good! :biggthumpup:
  14. Replies
    9
    Views
    2,107

    Radio Flyer All-Terrain Salvage/Tool Wagon

    I modified a used Radio Flyer wagon for use at the salvage yard to make things easier moving tools and picked parts around. I made a frame for it to increase the rigidity as well as a platform to...
  15. Replies
    32
    Views
    10,340

    The powder coater should have special high heat...

    The powder coater should have special high heat tape that they cover areas not to be coated.
  16. Thread: 148,000 miles

    by 98Dak408
    Replies
    18
    Views
    1,501

    Could also be worn valve guides/seals. I would...

    Could also be worn valve guides/seals. I would first look down the throttle body and see how much oil is sitting in the bottom of the intake manifold.
  17. Thread: Compression

    by 98Dak408
    Replies
    7
    Views
    1,382

    Deck heights can vary from engine to engine. ...

    Deck heights can vary from engine to engine. I've heard variations of .030-.060. I think I have a block under a tarp covered in snow. I may be able to measure it at some point. However, it is...
  18. Thread: Compression

    by 98Dak408
    Replies
    7
    Views
    1,382

    Try a combustion chamber volume of 59cc or 60cc....

    Try a combustion chamber volume of 59cc or 60cc. In past measurements I've found 59-60cc (un-ported) Edelbrock heads.

    https://i.imgur.com/wSHZhSf.jpg

    https://i.imgur.com/jGqr0Iv.jpg

    At 60cc...
  19. It's an LA head. It fits a Magnum but isn't...

    It's an LA head. It fits a Magnum but isn't cheap. It's a nice head but some Edelbrock's with good port work can work just as well.
  20. Replies
    13
    Views
    2,440

    Double check your spark energy. If you are...

    Double check your spark energy. If you are getting a bright white spark you should be good. If the spark is a dull yellow you likely aren't getting enough spark intensity. I've had back-to back bad...
  21. Replies
    3
    Views
    5,597

    Is the Challenger seat style year specific?

    Is the Challenger seat style year specific?
  22. Replies
    143
    Views
    41,377

    Funny! It does look like an old intake turtle. ...

    Funny! It does look like an old intake turtle. :biggthumpup:
  23. Replies
    143
    Views
    41,377

    The next step will probably be to make the merge...

    The next step will probably be to make the merge collector.
  24. Replies
    143
    Views
    41,377

    Fabricated the header spear (aka, spike, pyramid,...

    Fabricated the header spear (aka, spike, pyramid, bullet, etc.) that will be welded to the end of the header primary pipes within the collector, to improve exhaust scavenging.

    Cut some 2.375 long...
  25. Replies
    12
    Views
    15,111

    I suppose you could also make a mounting pad out...

    I suppose you could also make a mounting pad out of steel plate/sheet to better distribute the load over a wider area, if you already had a 4" concrete thickness to begin with. Maybe use more...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4