Search:

Type: Posts; User: Strokedrt

Page 1 of 5 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    26
    Views
    28,403

    What's the width on the rims if still available?

    What's the width on the rims if still available?
  2. Thread: My 99 CC R/T

    by Strokedrt
    Replies
    10
    Views
    3,922

    Thank you Rick for helping me post pictures of my...

    Thank you Rick for helping me post pictures of my truck:biggthumpup:
  3. Thread: My 99 CC R/T

    by Strokedrt
    Replies
    10
    Views
    3,922

    I will make a note of that. Thank you

    I will make a note of that. Thank you
  4. Thread: Drive shaft

    by Strokedrt
    Replies
    12
    Views
    7,878

    I have a custom carbon fiber drive shafts set up...

    I have a custom carbon fiber drive shafts set up for a 727 and ford 9 inch if you wake the swap :rockwoot:
  5. Thread: My 99 CC R/T

    by Strokedrt
    Replies
    10
    Views
    3,922

    10k , pics should be posted by end of weekend....

    10k , pics should be posted by end of weekend. Fellow forum member is going to help me post them.
  6. Thread: My 99 CC R/T

    by Strokedrt
    Replies
    10
    Views
    3,922

    Thank you

    Thank you
  7. Thread: My 99 CC R/T

    by Strokedrt
    Replies
    10
    Views
    3,922

    My 99 CC R/T

    Hello, everyone. :r/t smile:

    I'm not new to the forum but I definitely haven't posted much if any. I'm posting on the feelers section because I am not computer savy, at all. I don't know how to...
  8. Replies
    56
    Views
    7,467

    Indeed, once the throttle plates were adjusted...

    Indeed, once the throttle plates were adjusted and Ryan set the IAC counts, we are idling and running fairly well in the low power range. Time to start making some long W.O.T passes. (hopefully...
  9. Replies
    56
    Views
    7,467

    Sweet I did it... only took me 20 minutes to...

    Sweet I did it... only took me 20 minutes to figure out..lol
  10. Replies
    56
    Views
    7,467

    http://vid1344.photobucket.com/albums/p648/stroked...

    http://vid1344.photobucket.com/albums/p648/strokedrt/Mobile%20Uploads/20141110_164405_zpsvidiedtc.mp4
  11. Replies
    56
    Views
    7,467

    Sounds good to me, I appreciate it. Thank you

    Sounds good to me, I appreciate it. Thank you
  12. Replies
    56
    Views
    7,467

    I'll do that.. Thank you

    I'll do that.. Thank you
  13. Replies
    56
    Views
    7,467

    If I know how to add a video on here I would. I...

    If I know how to add a video on here I would. I have a short clip of it running when I did the idle screw method.
  14. Replies
    56
    Views
    7,467

    I was messing with the IAC today and plugging the...

    I was messing with the IAC today and plugging the hole on the F&B throttle body to see if there was any difference it idle quality and it seems as if the IAC isn't reacting fast enough. Aslo there...
  15. Replies
    56
    Views
    7,467

    I did pull all the plugs off the pcm and still...

    I did pull all the plugs off the pcm and still did a master rest using the scanner. Fuel syncbis set at 10, I think it's suppose to be at zero. It is extremely difficult for me to set because I can...
  16. Replies
    56
    Views
    7,467

    I tried that today using my snap on solus ultra....

    I tried that today using my snap on solus ultra. I reset all adaptations. Only codes are for trans. Governor sensor and another trans code I can't recall at this moment.
  17. Replies
    56
    Views
    7,467

    ****update**** Installed the front O2s right...

    ****update****

    Installed the front O2s right after the collectors and that wasn't my issue. Truck is still not holding idle. After all I have looked over I'm convinced it's going to be a tuning...
  18. Replies
    56
    Views
    7,467

    Will do

    Will do
  19. Replies
    56
    Views
    7,467

    Copy that... getting some bungs installed today...

    Copy that... getting some bungs installed today and installing them to see what happens.
  20. Replies
    56
    Views
    7,467

    I guess I can attempt to try that. I've tried to...

    I guess I can attempt to try that. I've tried to mimic that by placing some paper in between the adjusting screw and throttle mechanism but still wont hold idle. Unless my foot is on the throttle it...
  21. Replies
    56
    Views
    7,467

    If your referring to the pcm, I'm running the...

    If your referring to the pcm, I'm running the factory computer. The hand held programmer I'm using is the SCT hand held.
  22. Replies
    56
    Views
    7,467

    I was under that impression, I'm glad you chimed...

    I was under that impression, I'm glad you chimed in to verify my thoughts. I'll be hearing from Ryan tomorrow and hopefully we can figure this out. I dedicated tomorrow for this truck to get an idle...
  23. Replies
    56
    Views
    7,467

    My Local muffler shop has them.

    My Local muffler shop has them.
  24. Replies
    56
    Views
    7,467

    I think I may just weld in some o2 bungs today...

    I think I may just weld in some o2 bungs today and see what happens. I guess I was set in a mind set of the Tunes controlling the Air/Fuel ratio and the LM2 logging all of it. If it ends up being the...
  25. Replies
    56
    Views
    7,467

    I have no Idea... I could have swore that Ryan...

    I have no Idea... I could have swore that Ryan said I didn't need them. I'm going to wait to hear from Ryan and see what the verdict is. :idunno:
Results 1 to 25 of 110
Page 1 of 5 1 2 3 4