Search:

Type: Posts; User: jweltch

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    27
    Views
    23,113

    $8 sent, in case fees need to be covered.... ...

    $8 sent, in case fees need to be covered.... and whatever else.
  2. Replies
    40
    Views
    24,755

    $7.20 flat rate...

    $7.20 flat rate
    https://www.usps.com/ecp/asset/images/EP13PE-L0.jpg
  3. Replies
    55
    Views
    37,360

    My money is sent. I've been wondering what to do...

    My money is sent. I've been wondering what to do about this thing anyway.
  4. Replies
    3
    Views
    8,198

    Never put a wideband on it, but had a sniffer...

    Never put a wideband on it, but had a sniffer shoved up the pipe during a dyno run and it still went off the scale rich at WOT, even after the cats.
  5. Replies
    20
    Views
    5,445

    Lifters won't be the only thing collapsed if...

    Lifters won't be the only thing collapsed if you're spinning to 7500 on hydraulics! :teh finger:
  6. Replies
    20
    Views
    5,445

    I'm certainly no pro engine builder, but if...

    I'm certainly no pro engine builder, but if you're checking roller tip sweep with collapsed lifters then you aren't getting full lift and thus not the full sweep. It might not be enough to make a...
  7. Replies
    20
    Views
    5,445

    How did you check the sweep pattern of your...

    How did you check the sweep pattern of your rocker arms to the valve stem? Even with a lightweight checking spring the lifter will collapse a bit and skew your reading.

    Unless you're using solids...
  8. Replies
    20
    Views
    5,445

    I have one made up if you still need it.

    I have one made up if you still need it.
  9. My current build is using the stock crank and...

    My current build is using the stock crank and block with Eagle SiR rods and KB107s. The pistons all slightly protrude out of the deck, which affected my choice of head gasket. The .039" Fel-Pros...
  10. Replies
    124
    Views
    84,191

    Sticky: Bumping this old ass thread to see if there's any...

    Bumping this old ass thread to see if there's any info about upgrading an 01+ truck. Everything I'm able to find references pre-01's and I have an 03.
    It appears that the fuel pumps are different...
  11. Replies
    146
    Views
    88,692

    Got pics?

    Got pics?
  12. Thread: Arizona RT's

    by jweltch
    Replies
    173
    Views
    82,170

    I'm still around, but the R/T hasn't run in about...

    I'm still around, but the R/T hasn't run in about 5 years. Hoping that changes this winter...
  13. Replies
    12
    Views
    2,803

    If it's stock, just pick up a standard oil pump...

    If it's stock, just pick up a standard oil pump (I'm putting a Melling standard volume/pressure pump on my engine build - not a firebreather, but healthier than stock).

    If you take care of them...
  14. Replies
    12
    Views
    2,803

    I've heard from multiple sources that the rear...

    I've heard from multiple sources that the rear main likes to leak, even after it's been replaced. That doesn't mean it's supposed to, but it sounds like a fairly common issue. My Durango had a leak...
  15. Replies
    7
    Views
    1,921

    This. My Durango had this issue. I bypassed...

    This.

    My Durango had this issue. I bypassed the heater core every summer and it made a huge difference. It didn't help that I couldn't switch it to recirc so it was always pulling in outside air...
  16. Replies
    12
    Views
    2,803

    You're probably already done with everything and...

    You're probably already done with everything and have the truck back, but what the hell:

    That timing chain probably should have been replaced 90,000mi ago anyway.
    Might as well replace the oil...
  17. Thread: FRP- Tuning

    by jweltch
    Replies
    13
    Views
    6,723

    Hemifever seems to be pretty popular with the...

    Hemifever seems to be pretty popular with the Hemi guys. I've heard of HemiTuner, but not sure how well known (or used) he is.

    Ryan (FRP) has been working with me on a canned tune for my 14 Hemi...
  18. Replies
    1
    Views
    1,159

    Hemifever update

    I can't post this in his subforum so here it is.

    For those of you who still have a Hemifever tune, he just posted this on his Facebook page earlier today.

    13667
  19. Replies
    10
    Views
    2,174

    Hmm.. He's looking for an engine builder,...

    Hmm..

    He's looking for an engine builder, and I don't see any mention of porting.

    But you recommend avoiding a semi-well known engine shop completely because of a single experience with some...
  20. I hope this happens soon. I don't dislike...

    I hope this happens soon. I don't dislike Paypal, but I sure was irritated trying to link a Wells Fargo card to my account last night for a tune on my Ram...
  21. Replies
    9
    Views
    2,604

    Shipped. Check your PMs for tracking number

    Shipped. Check your PMs for tracking number
  22. Replies
    9
    Views
    2,604

    If you still want it, I can do that. paypal to...

    If you still want it, I can do that. paypal to jweltch@gmail.com
  23. Replies
    9
    Views
    2,604

    :secret squirrel: I forgot I already had a...

    :secret squirrel:

    I forgot I already had a spare, then I sold the Durango. I don't need 2 of these for the Dakota.
    Want it back? :)
  24. Replies
    9
    Views
    2,604

    Price dropped.

    Price dropped.
  25. Replies
    9
    Views
    2,604

    01-03 Console lid / Arm Rest thing...

    sold

    https://scontent-lax3-1.xx.fbcdn.net/hphotos-xfp1/t31.0-8/12622138_10206742083324965_9032742366874063317_o.jpg
    ...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4