There is no such thing as a torque converter for a 360. Torque converter from a 318 does not swap to a 360. D style and C style do not mix , keep your torque converter it will work just fine. I...
Type: Posts; User: Electrical Tech
There is no such thing as a torque converter for a 360. Torque converter from a 318 does not swap to a 360. D style and C style do not mix , keep your torque converter it will work just fine. I...
You are good with the 8.8 as it has a speed sensor and has either 104 teeth or 108. The actual speed sensor works as well too they are simply mag pickups and are two wire so they are passive. I...
What years will this fit? I need one for my 99 Dakota and have seen some connector differences in the years.
Have a Fuel cell question, I just installed my fuel cell finally and I am using the 10AN feed and 8AN return that are at the bottom in the front of the cell. I have two more 8AN ports on the top of...
Facebook video was great! Good motivation to finish my fuel system.
I am interested in the grille and do have a stock one to trade for it. Contact me at m.colantuoni@hotmail.com
Mike,
Okay, I have seen enough. I will buy the kit, email me at m.colantuoni@hotmail.com and I can pay through paypal if you want.
Mike,
1 248 921 9534
I found an AC delete bracket w/pulley in the boneyard, if someone wants it just give an address and I can send it to you. Call it $10 for shipping.
Mike,
m.colantuoni@hotmail.com
Thanks for the input, looks like 8AN up to the rails is a must. I see a few ways to plumb the regulator. "SB440 R/T" looks like you have your fuel rails plumbed into the inlet and outlet of the...
Looking for any diagrams on how to setup a Return style fuel system. I have relocated my tank to the bed and have fuel rails on the way. I plan on doing the return style with the regulator...
I would like to buy these fuel rails for my Dakota 408 with a 2BL M1 intake. Can you recommend a fuel pump and regulator to be used with a relocated tank in the bed? Do I go with a return or...
Spring perches are a different width as well to fit the Durango has a wider frame. Does the Durango have the same gear ratio?
Mike,
6119
6120
Try these, 1998 Dakota Hurst shifter
If you want your speedo recalibrated the dealership can do it by changing the axle from 8.25 to 9.25 on the handheld. I have heard that some Snap-on models will do it through the antilock brake or...
I have a set of 4.56 gears for a 99 Dakota but its for the 8.25 rear end with the stock LSD carrier, and PML cover. I also have the front 4WD axle with 4.56 gears for the same year.
Real cheap,...
Schumacher has a Trans mount for this 727 swap.
Good excuse to upgrade the driveshaft anyway. Got mine for $260 3.5" steel and 1350 U-joints.
I am in the process of relocating the CPS sensor...
The dealership can do it but they charge 1 hr of labor.
They will need to know the rear end 9.25" which is 108 teeth.
The 8.25" is 104 teeth.
If the tire size is not listed on the scanner then...
Guess I went a bit overboard and unbolted the body mounts and lifted the cab an inch to get the bolts out. I did it on my 4-wheel drives a few times and its very easy.
Mike
I just did the same thing on my truck. I put in a 727 and wanted to run a 3500 Stall converter that we had on hand rather than a custom one from Msaine. I used the MSD crank trigger mount and had 8...
I have one with the lines and support brackets. I pulled it from a standard truck in the boneyard so it was never used and had the factory yellow caps on the ends. I will be back home in a week and...
Too funny........
I would be interested in seeing 5X4.5" front hubs made for the 98 Dakota. I already have a 5X4.5" pattern for the rear with the Mopar 8 3/4" rear end. Let me know what the price is and if the...
I have a new minispool for a 9" sitting here and a full spool with a speed ring mounted on it. email me at m.colantuoni@hotmail.com if interested $50 for both.
Mike,
Thanks for clearing that up I had my figures on 1.6RR not 1.5 . Not sure why KRC had it ground on a 108 rather 110, I will edit the first post. Like I said the cam was fantastic with the 2.02...
Here is the card. The 1.7 RR raise the height from .475 to .504 from my calculation. I ran this cam in a stock 360 with 2.02 heads and it was great, changed heads back to stock and had a very rough...