FRP
  • Latest Classifieds

  • Recent Forum Posts

    Duner

    What worked and didn't

    Boost.
    However you can get it.

    Duner Today, 12:29 PM Go to last post
    wdh681

    How do I know if the a/c condenser is messed up?

    The rule of thumb that I was told is you want a 30 degree temperature difference between ambient and outlet temp. Humidity also plays a factor into it.

    wdh681 Today, 06:17 AM Go to last post
    SynRG

    New best today.

    Either the something in the VB is messed up or TC is going out causing all the problems. When cold, truck barely moves in any gear. Can rev to 4K and

    SynRG Today, 05:57 AM Go to last post
    Adobedude

    What worked and didn't

    Carb FTW.

    Adobedude Today, 03:55 AM Go to last post
    madboy

    Axle Tubes

    Most on the East coast

    madboy Today, 03:38 AM Go to last post
  • Recent Activity Widget

    Filthy Filbert

    Summer give away raffle!!

    Thread Starter: Filthy Filbert

    Announcing this year's raffle/door prize giveaways. As you all know by now, in lieu of a single national meet, we've advocated that each division...

    Last Post By: chase1500 Yesterday, 02:10 PM Go to last post
    Friggin' R/T

    2nd time out

    Thread Starter: Friggin' R/T

    heading to the track tomorrow after work to test out drag radials. Any tips?

    Last Post By: 5 NINER Today, 01:14 AM Go to last post
    PredatorySith

    Tuners

    Thread Starter: PredatorySith

    What is the best bang for tour buck when it comes to tuners? Ive done a lot of research but id like to hear from people instead of websites. They'll...

    Last Post By: FlyinRyan Today, 01:29 AM Go to last post
    niebs

    FRP- Tuning

    Thread Starter: niebs

    Hey does ryan tune hemis with hp? I'm on a charger/challenger/ 300 forum and they seem to only be going to hemifever for their tunes.

    Last Post By: Slowkoda Yesterday, 09:13 PM Go to last post
    SynRG

    New best today.

    Thread Starter: SynRG

    14.32 @ 100.54 MPH. DA in the 3000 area. 26" Drag radials, no tonneau, sport wheels all around, no back seat and had slapper bars on.

    Last Post By: SynRG Today, 05:57 AM Go to last post
    mikset

    Axle Tubes

    Thread Starter: mikset

    This feels like a dumb question but is it ok to leave my truck supported by jack stands under the axle tubes for several days? Any chance of damaging...

    Last Post By: madboy Today, 03:38 AM Go to last post
    wh23g3g

    Belt or pulley squeal I can't locate

    Thread Starter: wh23g3g

    I recently had my water pump and timing cover gasket changed and I still have a squeal. It was doing it a little before I had this changed but now...

    Last Post By: wh23g3g Today, 01:45 AM Go to last post
    Mnrt

    Engine builder in minnesota

    Thread Starter: Mnrt

    I live in cloquet mn does any one know of any good engine builders in my area I need to contact someone about the right head an cam combo for my...

    Last Post By: Mnrt Yesterday, 11:49 PM Go to last post
    arro222

    What worked and didn't

    Thread Starter: arro222

    In the attempt to make our trucks faster, there are a bunch of what can be called "standard" components that were supposed to excite more speed out...

    Last Post By: Duner Today, 12:29 PM Go to last post
    wh23g3g

    How do I know if the a/c condenser is messed up?

    Thread Starter: wh23g3g

    So back to the a/c performance problems. I tested my pressures on a 88 degree day with a low reading of around 35 and high reading of 200. According...

    Last Post By: wdh681 Today, 06:17 AM Go to last post