• Announcing new club secretary!

    The DRTC is happy to announce the confirmation of our new secretary Rudy Reyes (SynRG)! He is motivated and excited to step up to the plate and start helping out with admin duties and keeping the club going! Please allow for some bumps along the way as we get the club supplies sent out to Rudy and get him set up with the club accounts and accesses.
    Comments 5 Comments
    1. ScojoDak's Avatar
      ScojoDak -
      Good choice. Congrats Rudy
    1. Steve '02CC's Avatar
      Steve '02CC -
      CONGRATS RUDY!
      Want 100lbs of tshirts?
    1. Kingst3r's Avatar
      Kingst3r -
      Nice choice. Congrats man
    1. SynRG's Avatar
      SynRG -
      Thanks guys!
    1. Roos's Avatar
      Roos -
      Rudy did you get my message
  • Latest Classifieds

  • Recent Forum Posts

    98Dak408

    What did you do to your R/T today?

    Got a killer deal on a Larson spring tester PAC-T935. Very nice piece of equipment.

    I previously had a Proform but it didn't last long.

    98Dak408 Today, 09:23 PM Go to last post
    1999r/t

    back in a dak again

    not 100 percent new just back in a Dakota rt again. 7 years is way to long. white is the new. yellow was the old. what did i miss??? anything important???

    1999r/t Today, 08:16 PM Go to last post
    nitroram33

    5 lug conversion

    Extra leverage helps a bunch lol. Like I said though, the biggest to using all the Mustang stuff is that parts are readily available with no modifications

    nitroram33 Today, 06:26 PM Go to last post
    Osee

    5 lug conversion

    I was looking and the gt calipers have dual 41.5mm pistons where as the dakota has dual 50mm pistons. If I switch to gt calipers I know I'll have a much

    Osee Today, 05:18 PM Go to last post
    JDreamR/T

    What did you do to your R/T today?

    Thanks! I had previously addressed the issue by sanding the roof and coating in red rustoleum spray paint. I'm much more pleased with the look of the

    JDreamR/T Today, 03:24 PM Go to last post
  • Recent Activity Widget

    Kingst3r

    What did you do to your R/T today?

    Thread Starter: Kingst3r

    Figured we could use something new to read. Simply post what you did to your r/t (or dakota) today. It could be anything big like pulling a motor...

    Last Post By: 98Dak408 Today, 09:23 PM Go to last post
    MonsterDak

    99 Dakota part out

    Thread Starter: MonsterDak

    Posting here for now until I get pics and a little warmer weather comes unless I get a lot of interest. Prices may change if I seen something not...

    Last Post By: MonsterDak Today, 12:22 PM Go to last post
    jeffru6475

    c-clip removal

    Thread Starter: jeffru6475

    I'm trying to get started with my build and crap. If i use stock rear , i have to change the housing ends plus brakes ? I'm trying to add this all up...

    Last Post By: Filthy Filbert Today, 01:17 PM Go to last post
    THEhomelessONE

    High torque 408 cam recommendations? M1 4bbl vs AirGap?

    Thread Starter: THEhomelessONE

    Jeep weighs 5k lbs with tall gearing. Stuck using a single 3" exhaust with a cat. I'd like to shift at 6k and run a low stall or a really tight...

    Last Post By: pplhz03rt Today, 12:05 AM Go to last post
    themoparman

    5 lug conversion

    Thread Starter: themoparman

    Some of you know I just adopted Don' s R/T. I'm want some advice on a 5 lug conversion plus a upgrade to a disc brakes conversion at all four...

    Last Post By: nitroram33 Today, 06:26 PM Go to last post
    TUC_Truck

    Arizona R/T

    Thread Starter: TUC_Truck

    Whats up guys, just saying hi from Tucson, Arizona. Joined a long time ago but the Dakota took a backseat to life unfortunately so I wasn't active on...

    Last Post By: y2krtaf Today, 02:06 PM Go to last post
    wh23g3g

    General Question on Leak Down Testing and Compression Testing

    Thread Starter: wh23g3g

    I need to get a leak down test to see if my engine is still good but not on my 5.9 it's a 4 Cylinder OHC engine but I can't find a mechanic shop in...

    Last Post By: Filthy Filbert Today, 01:15 PM Go to last post