PDA

View Full Version : Raped Ape dyno results



Lonesoldier79
03-13-2014, 08:57 PM
Well today was pretty much a waste. I couldn't get the SCT software to work and SCT tech support couldn't help either. I had one pull done to get the fuel trim at idle, 25, 50 and AF at WOT. I got two more tunes sent but was unable to uploaded onto the X2 and did not get her dialed in. I have another session set up on the 25th and I will have whatever the driver/software issue was taken care of.

9144

Addicted2Blue00
03-13-2014, 09:06 PM
not bad but atleast you can guess what could be left on the table when you do get it tuned. youll be grinning ear to ear next time. wheres the video of this said "dyno session"?

RTchas
03-13-2014, 09:14 PM
I've been there with SCT trouble's it suck's.

Virus software was F'n up my download couldn't get tune to load right had to go to PIE have him do it @ the shop.

Now you have a base and once you square away the Drive BS you'll be happy to see some real number's!

Next time shoot some video of that Beast on the Dyno making loud noise!!

You'll get it working!

Five9Dak
03-13-2014, 09:52 PM
That is an NA pull, correct?

Lonesoldier79
03-13-2014, 10:32 PM
That is an NA pull, correct?

Yeah it's N/A on a start up tune. Once I get on the dyno again with the new tunes Chris sent me I should see my goal of 300whp or pretty close too it. I'm only 23hp away.

The paxton wont be going on the truck until July unless I hit the lottery :biggthumpup:

Lonesoldier79
03-13-2014, 10:35 PM
not bad but atleast you can guess what could be left on the table when you do get it tuned. youll be grinning ear to ear next time. wheres the video of this said "dyno session"?


I've been there with SCT trouble's it suck's.

Virus software was F'n up my download couldn't get tune to load right had to go to PIE have him do it @ the shop.

Now you have a base and once you square away the Drive BS you'll be happy to see some real number's!

Next time shoot some video of that Beast on the Dyno making loud noise!!

You'll get it working!

I was so excited to be on a dyno I forgot to shoot video. After the first and only pull I was too embarassed to shoot a video of me sitting for an hour on the phone with SCT tech support and the guys at Mayhem looking at me like a complete fool......lol I promise next time I will take a video :biggthumpup:

Lonesoldier79
03-13-2014, 11:29 PM
It's not the video you wanted to see but I think you'll like it :r/t smile:

http://s1267.photobucket.com/user/egnder/media/Dakota%20RT/3-13-14burnout_zps33f5b407.mp4.html

Addicted2Blue00
03-14-2014, 02:27 AM
:hitit2:

moparmadman
03-14-2014, 04:00 AM
Screw the old lady down the road!!!! :r/t smile:

Lonesoldier79
03-15-2014, 02:02 AM
Screw the old lady down the road!!!! :r/t smile:

20 years ago I might have......I hope you enjoyed the burnout as much as I did!

moparmadman
03-15-2014, 02:57 AM
I think we're using two different definitions of the word screw :jester:

1995dak
03-15-2014, 05:40 PM
Truck sounds good buddy! Glad you got it up and running. I bet your having a blast. :drive:

Lonesoldier79
03-25-2014, 09:54 PM
I had a second dyno session today and I am happy to say that I hit my goal of 300whp.

http://s1267.photobucket.com/user/egnder/media/Dakota%20RT/3-25-14dynosession_zps25fe77ac.mp4.html

perfinj
03-26-2014, 12:37 AM
Eric I am happy all went well and that we met our goal. If we would have had one more pull I think we could have picked up some more power. If you use that dyno place again I would tell them to use wheel chocks on the dyno and tighten the strap. Watching the video I thought it was getting ready to drive off the dyno.

Lonesoldier79
03-26-2014, 12:48 AM
Eric I am happy all went well and that we met our goal. If we would have had one more pull I think we could have picked up some more power. If you use that dyno place again I would tell them to use wheel chocks on the dyno and tighten the strap. Watching the video I thought it was getting ready to drive off the dyno.

Will do sir! I might do another hour session in a few weeks. I have the cheap autolite spark plugs in right now and are were gapped to .040. The iginition I am running supposedly can be gapped to .065 and I just picked up some NKG's I am going to gap to .050 for shits and giggles to see if it makes any difference. If I gain a couple HP over the stock plugs then it's worth the $17 bucks. That place only charged me $75.00 for an hour today and I wish I would have booked two hours so I could have sent more runfiles to you to get a couple more pulls. I'm not too worried about it because the paxton will be going on soon enough :biggthumpup: I'm looking forward to making the trip north and seeing how PIE gets down :drive:

White Turbo
03-26-2014, 03:40 AM
Nice results Eric!
:r/t smile:

Gettin' it dialed in now.

:drtc_logo001:

Five9Dak
03-26-2014, 11:35 AM
Glad the combination is working the way you hoped.

RTchas
03-27-2014, 05:20 PM
Nice Work!