PDA

View Full Version : m1 pics

01dakotaR/T
05-05-2008, 08:30 PM
here are some pics of my m1 installed. i got alot more planned so stay tuned.

http://i143.photobucket.com/albums/r160/01dakotaqc/100_1464.jpg

http://i143.photobucket.com/albums/r160/01dakotaqc/100_1463-1.jpg

http://i143.photobucket.com/albums/r160/01dakotaqc/100_1465.jpg
emwhiteR/T
05-05-2008, 09:39 PM
Nice job. I can't tell from the pics but you may want to relocate your map sensor vacuum from the TB to the M1.

I had to do that because I would get a slight stumble off the line when I hit the gas.

It was recommended to me and it worked so I am passing it on to you!
01dakotaR/T
05-05-2008, 10:34 PM
Nice job. I can't tell from the pics but you may want to relocate your map sensor vacuum from the TB to the M1.

I had to do that because I would get a slight stumble off the line when I hit the gas.

It was recommended to me and it worked so I am passing it on to you!

the sensor on the front of the throttle body?? let me know and ill change it. thanks for the info.
emwhiteR/T
05-05-2008, 11:30 PM
the sensor on the front of the throttle body?? let me know and ill change it. thanks for the info.

Yuppers! It should have a tiny elbow that connects it to the TB. Just relocate it to the M1.
01dakotaR/T
05-06-2008, 10:41 AM
Yuppers! It should have a tiny elbow that connects it to the TB. Just relocate it to the M1.

k thanks. ill do that today.
Five9Dak
05-06-2008, 03:54 PM
It's probably obvious but make sure you cap off the port on the throttle body that you disconnect the MAP from. Also you can re-locate your IAT from the M1 to your cold air intake, you will need (I believe) a 1/4" NPT pipe plug, like 20 cents at the hardware store.
01dakotaR/T
05-06-2008, 06:54 PM
It's probably obvious but make sure you cap off the port on the throttle body that you disconnect the MAP from. Also you can re-locate your IAT from the M1 to your cold air intake, you will need (I believe) a 1/4" NPT pipe plug, like 20 cents at the hardware store.

yeah i know. i cant find a hose the right size. the inlet on the map is smaller than the manifold inlet. i cant put 2 hoses together either. where can i find a coupler to join the two different size hoses together?? is there an easier way of doin this?
emwhiteR/T
05-07-2008, 04:55 AM
yeah i know. i cant find a hose the right size. the inlet on the map is smaller than the manifold inlet. i cant put 2 hoses together either. where can i find a coupler to join the two different size hoses together?? is there an easier way of doin this?

I went to Autozone and bought a small box full of vacuum line connectors. They will step from one size to another. I also bought a small box of vacuum caps from there too.

I don't remember the size of the hoses but I walked into Autozone and had them dig out the MAP sensor and then match up a hose to it. Bring one of the plugs for the M1 ports in to the store and have them match up a size of the hose to it.
01dakotaR/T
05-07-2008, 10:55 AM
I went to Autozone and bought a small box full of vacuum line connectors. They will step from one size to another. I also bought a small box of vacuum caps from there too.

I don't remember the size of the hoses but I walked into Autozone and had them dig out the MAP sensor and then match up a hose to it. Bring one of the plugs for the M1 ports in to the store and have them match up a size of the hose to it.

ok thanks. ill try that today.