Extreme Velocity air hat

[magnuma1]

Is this air hat any good? I see a lot of people using them. What size would I need for a 52 mm TB? How do they bolt to the TB? I noticed that a few of the different TB's have the bolt hole in different places. One had 2 mounting holes and others had just 1 (like the holley that I have has just 1 mounting hole).
Mike

[Trueblue R/T]

Is this air hat any good? I see a lot of people using them. What size would I need for a 52 mm TB? How do they bolt to the TB? I noticed that a few of the different TB's have the bolt hole in different places. One had 2 mounting holes and others had just 1 (like the holley that I have has just 1 mounting hole).
Mike

read this thread about daves motor,,the extreme air hat was actuallu compared on the dyno results might suprise you..

http://www.dakotart.com/forum/showthread.php?t=1235

[magnuma1]

read this thread about daves motor,,the extreme air hat was actuallu compared on the dyno results might suprise you..

http://www.dakotart.com/forum/showthread.php?t=1235

I don't see where it says anything about it. Can you point it out for me.
Thanks.
Mike

[Nolan]

Actually the thread is this one
http://board.moparts.org/ubbthreads/showflat.php?Cat=0&Number=4340735&an=0&page=0#Post4340735

I think they were talking about the K&N Extreme air cleaner lid and not the Extreme Velocity air hat.
"We were testing air cleaner VS no AC, & testing a K&N Xtreme lid at the time so that's why no Airflow & AF etc on this pull. The K&N 3"X14" AC lost around 8 HP.... When we blocked off the Xtreme lid with duct tape it gained power back...... "

Nolan

[TurboBlew]

Is this air hat any good? I see a lot of people using them. What size would I need for a 52 mm TB? How do they bolt to the TB? I noticed that a few of the different TB's have the bolt hole in different places. One had 2 mounting holes and others had just 1 (like the holley that I have has just 1 mounting hole).
Mike

standard carb mounting size is 5 1/8"

They are more beneficial for high pressure forced induction setups.

[mtlcafan79]

Yeah, somebody is confused.

http://www.superiorairflow.com/EVPA-00.jpg

is not the same as:

http://www.dragstuff.com/classifieds/data/2/2702-9_010.jpg

[Trueblue R/T]

Yeah, somebody is confused.

http://www.superiorairflow.com/EVPA-00.jpg

is not the same as:

http://www.dragstuff.com/classifieds/data/2/2702-9_010.jpg

lol my bad

[magnuma1]

standard carb mounting size is 5 1/8"

They are more beneficial for high pressure forced induction setups.

Do you know of a good place to buy 1? And is there different models, some with o-ring gaskets and stuff. Which 1 is the one that everyone is getting?

Mike

[TurboBlew]

Do you know of a good place to buy 1? And is there different models, some with o-ring gaskets and stuff. Which 1 is the one that everyone is getting?

Mike

heres a start
http://www.superiorairflow.com/

I think Mopar318 had a link for a spectre knockoff that was about 1/3 the price.

Otherwise try ebay

[magnuma1]

heres a start
http://www.superiorairflow.com/

I think Mopar318 had a link for a spectre knockoff that was about 1/3 the price.

Otherwise try ebay

Do you know which model?
Mike

[TurboBlew]

that would depend on what kinda charge pipe youre running. 3"? 4"?

[Mopar318]

Do you know which model?
Mike

Its not really a knock off, a little different design, and cost about 70 bucks. I'm sure it doesn't flow as good as the superior air flow hat, but for a moderate boost and half grand power levels its fairly insignificant.

Heres (http://cgi.ebay.com/ebaymotors/Blow-Through-Carb-Hat-Throttle-Body-Turbo-Bonnet_W0QQcmdZViewItemQQ_trksidZp1638Q2em118Q2el1 247QQcategoryZ38634QQihZ023QQitemZ360028811932QQrd Z1QQsspagenameZWD1V) a link on ebay that sells them.

Heres a real life picture on my setup.

http://i32.photobucket.com/albums/d48/Mopar318/Chevelle/Today003.jpg

I used a 45 degree 4"-3" adapater, which will run about 15 bucks from frozenboost.com

[John]

Actually the thread is this one
http://board.moparts.org/ubbthreads/showflat.php?Cat=0&Number=4340735&an=0&page=0#Post4340735

I think they were talking about the K&N Extreme air cleaner lid and not the Extreme Velocity air hat.
"We were testing air cleaner VS no AC, & testing a K&N Xtreme lid at the time so that's why no Airflow & AF etc on this pull. The K&N 3"X14" AC lost around 8 HP.... When we blocked off the Xtreme lid with duct tape it gained power back...... "

Nolan

sorry to keep the thread jack going but the x-stream top actually killed off some power? was he running FI or carb for the test?

[uwntsumrtII]

sorry to keep the thread jack going but the x-stream top actually killed off some power? was he running FI or carb for the test?

carbed