Activity Stream
-
Older Activity
-
09-30-2023, 12:04 AMMade and installed both risers. I may have to make them taller for ease of installation, but I don't have a whole lot of head room unless I extend...14 replies | 754 view(s)
-
09-30-2023, 12:00 AMSomething to think about. :biggthumpup:14 replies | 754 view(s)
-
09-29-2023, 10:26 PMI will probably go that route.10 replies | 439 view(s) -
09-29-2023, 10:26 PMI will probably go that route.10 replies | 439 view(s)
-
09-29-2023, 10:25 PMI ordered from shopeddys in california. He is contacting fedex now.10 replies | 439 view(s)
-
09-29-2023, 06:12 PMMaybe a short arm will help then? Just make sure you have full engagement so that you don't strip the hex. You can buy or modify your own....10 replies | 439 view(s)
-
09-29-2023, 04:47 PMA dual 4 version of the Dodge 6 pack would look good.14 replies | 754 view(s)
-
09-29-2023, 01:43 AMI made a test riser out of sheet metal that will allow me to fasten the air cleaner to the throttle body.14 replies | 754 view(s)
-
09-29-2023, 01:34 AMI picked up a Lancaster shrinker and stretcher for sheet metal. I decided to make a foot operated stand for it for better precision and ease of use....0 replies | 62 view(s)
-
09-29-2023, 12:44 AMmine has allen bolts holding headers to plates. Hit a roadblock as my gaskets ended up in miami and have been delayed. Was supposed to arrive a week...10 replies | 439 view(s)
-
09-28-2023, 06:10 PMYes Mike, it's the Golden West Kit. Same one you had seen at Topeka 2001.21 replies | 8206 view(s)
-
09-28-2023, 05:16 AMUsing stock hood springs. The hood I have came directly from Pro Glass, and was one of the 1st hoods they made. It weighs approx. 5 lbs more that...23 replies | 3838 view(s)
-
09-25-2023, 09:17 PM^^^ That is what I was suggesting, not as clear though...^^^23 replies | 3838 view(s)
-
09-25-2023, 07:20 PMI'm getting it from a guy in Georgia. Are you using the stock hood springs or did you go to a strut mount for your shaker hood?23 replies | 3838 view(s)
-
09-25-2023, 02:02 PMUse one of the base plates I sent you the link for. I had to make a spacer to go between the throttle body and the intake, so the shaker would look...23 replies | 3838 view(s)
-
09-25-2023, 12:42 PMYes, if I can't find a 1" rise base plate I will do that. I have a 1/4" spacer now between the K/N cold air intake and TB, but it not as robust as...23 replies | 3838 view(s)
-
09-25-2023, 01:39 AMMike , what’s up how ya been21 replies | 8206 view(s)
-
09-25-2023, 01:07 AMWould adding a 1/4" between the throttle body and the intake get it to the 1" required?23 replies | 3838 view(s)
-
09-24-2023, 05:03 PMAll the links, show base plates with 3/4" rise, not 1". I couldn't find any 1" rise base plates, that's why I asked.23 replies | 3838 view(s)
-
09-24-2023, 12:07 PMhttps://www.summitracing.com/parts/trd-2429 https://www.summitracing.com/parts/kns-ka501223 replies | 3838 view(s)
-
09-24-2023, 12:04 PMhttps://www.summitracing.com/parts/sum-239465/department/air-fuel-delivery/section/air-cleaners-flame-arrestors-scoops/part-type/air-cleaner-bottoms23 replies | 3838 view(s)
-
09-24-2023, 11:57 AMYou can't use a drop base bottom. It has to be a 1" rise bottom plate. That is usually what any cheap air cleaner would come with. ...23 replies | 3838 view(s)
-
09-23-2023, 01:01 PMWhat brand and size tires are on your truck?5 replies | 2699 view(s)
-
09-23-2023, 12:31 PMCan anyone confirm you need a 14" base with 1" rise to mount Shaker box. I can't find a 14" base with a 1" rise, only 3/4" rise.23 replies | 3838 view(s)
-
09-22-2023, 04:32 PMYou can have that problem with aluminum and steel too. My father had an old Korean War army truck that he modified for a snowplow. He made thick...10 replies | 439 view(s)
-
09-22-2023, 03:25 PMYes, anti-seize with aluminum to stainless is a MUST! I rarely install ANY bolt without anti-seize or some sort of thread sealant anymore.10 replies | 439 view(s)
-
09-22-2023, 08:13 AMFor posterity.. https://www.mecum.com/lots/1097805/2000-dodge-dakota-r-t-pickup/21 replies | 8206 view(s)
-
09-22-2023, 07:32 AMIs that one of the original Golden West ProCharger kits? Hope you don't have regrets later. Someone's going to be happy. Worth every penny. Great...21 replies | 8206 view(s)
-
09-22-2023, 01:50 AM:rockwoot:21 replies | 8206 view(s)
-
09-22-2023, 01:27 AMToday I sold my truck at Mecum (T279). Had this one for 23 years. Great truck! The good news is, if you have a super clean truck without rust the...21 replies | 8206 view(s)
