Activity Stream
-
Older Activity
-
Today, 12:41 AMNever tried this job in the truck, but below is a snapshot of the service manual instructions for ya if it helps any...6 replies | 137 view(s)
-
Yesterday, 03:07 PMYou can't rent one or find one on craigslist that can be sold after using? I would pull the engine and replace the core plugs while doing the...6 replies | 137 view(s)
-
Yesterday, 01:29 PMI started to remove/loosen bolts to raise the engine. I searched youtube, but can't find where anyone has done a 5.2/5.9 2wd before. Will there be...6 replies | 137 view(s) -
Yesterday, 12:54 PM98Dak408 replied to a thread What's an affordable OBD2 scanner that will pickup these transmission codes? in Troubleshooter ForumThe Snap-On MT-2500 will do that and they can now be found for under $200 on ebay. .4 replies | 39 view(s)
-
Yesterday, 12:52 PM98Dak408 replied to a thread What's an affordable OBD2 scanner that will pickup these transmission codes? in Troubleshooter ForumUnfortunately, these vehicles don't always throw appropriate codes when something is wrong.4 replies | 39 view(s)
-
Yesterday, 07:45 AMJDreamR/T replied to a thread What's an affordable OBD2 scanner that will pickup these transmission codes? in Troubleshooter ForumNot to thread jack, but anyone know of a decent scan tool to set fuel sync with? Is DRB3 the only option? I've seen DRB3 emulators online, was...4 replies | 39 view(s)
-
Yesterday, 05:14 AMThanks all, yes very relieved that it was a simple fix, sucks to open things up again but not bad considering the alternatives in my brain. I got...143 replies | 11621 view(s)
-
Yesterday, 02:15 AMarro222 replied to a thread What's an affordable OBD2 scanner that will pickup these transmission codes? in Troubleshooter ForumWho did the work on the tranny? You may have a cracked or loose wire going to the position shift sensor. (outside of tranny) The other thing might...4 replies | 39 view(s)
-
03-02-2021, 11:14 PMwh23g3g started a thread What's an affordable OBD2 scanner that will pickup these transmission codes? in Troubleshooter ForumMy obd2 scanner doesn't pickup when my 99 get's a transmission code. All I've got is a fairly standard Autel scanner from Harborfreight since I don't...4 replies | 39 view(s)
-
03-02-2021, 02:41 PM:biggthumpup:143 replies | 11621 view(s)
-
03-02-2021, 01:58 PM:rockwoot::rockwoot: WooHoo! SOoooooo glad it was a (relatively) easy fix! :r/t smile::r/t smile:143 replies | 11621 view(s)
-
03-02-2021, 07:07 AMSweet ! Glad you got it fixed143 replies | 11621 view(s)
-
03-02-2021, 03:45 AMSmoking gun...glad you found the problem.143 replies | 11621 view(s)
-
03-02-2021, 02:31 AMTook apart the timing set and it revealed I indeed was missing the oil gallery plugs. All fixed up now thanks again to Pat and Lloyd!143 replies | 11621 view(s)
-
03-02-2021, 02:20 AMLol! Yeah it's about as big haha. Thanks for that info, Dynomax definitely a quality brand, I might give that a shot I know I'll be...143 replies | 11621 view(s)
-
03-02-2021, 01:58 AM98Dak408 replied to a thread HiPoTek Prototype LA Conversion Motor Mounts 1987-1996 Dakota in HiPoTekThanks Jim!8 replies | 193 view(s)
-
03-01-2021, 11:58 PMWhoa...The pictures make that muffler look like a gas tank! LOL But, I like your thinking! Something different...outside that overused box. ...143 replies | 11621 view(s)
-
03-01-2021, 11:52 PMyou know what sounds really good and has almost no restriction, reasonably quiet at idle and light throttle, and sounds really good but not obnoxious...143 replies | 11621 view(s)
-
03-01-2021, 08:20 PMonce my 493 stroker is fully warmed up (at least 10 minutes of run time) it has low oil pressure when it's under 800 rpm. But that is due to the...143 replies | 11621 view(s)
-
03-01-2021, 08:14 PMyou know what sounds really good and has almost no restriction, reasonably quiet at idle and light throttle, and sounds really good but not obnoxious...143 replies | 11621 view(s)
-
03-01-2021, 08:00 PMNice job, can't wait to see it done and hear it. I have the full SpinTech with the side exit before the wheel and it's too loud for me. First, I'm...143 replies | 11621 view(s)
-
03-01-2021, 06:43 PMSo here's a quick 5 min video update of running the engine with the manual oil pressure test gauge. Warning you may want to turn down your volume,...143 replies | 11621 view(s)
-
03-01-2021, 06:30 PM:biggthumpup:20 replies | 2162 view(s)
-
03-01-2021, 06:24 PMJDreamR/T replied to a thread HiPoTek Prototype LA Conversion Motor Mounts 1987-1996 Dakota in HiPoTekKiller design and fab work as always Richard! :You_Rock_Emoticon:8 replies | 193 view(s)
-
03-01-2021, 05:23 PMStay tempted, and come on down! I fire her up weekly, but she hasn't moved in a few months. My daughter loves to sit inside and 'drive' and beep...20 replies | 2162 view(s)
-
03-01-2021, 03:33 AMblackknight replied to a thread HiPoTek Prototype LA Conversion Motor Mounts 1987-1996 Dakota in HiPoTekMan those look sweet !8 replies | 193 view(s)
-
03-01-2021, 01:57 AM:biggthumpup:11 replies | 175 view(s)
-
03-01-2021, 01:44 AMJust wanted to thank you. I do believe taking a few thousands off the pins worked, they were seizing up only when you tighten up the caliper bolts.11 replies | 175 view(s)
-
02-28-2021, 11:15 PM98Dak408 replied to a thread HiPoTek Prototype LA Conversion Motor Mounts 1987-1996 Dakota in HiPoTekYeah.8 replies | 193 view(s)
-
02-28-2021, 10:21 PMLol, thanks dude honestly I'm just finally getting around to catching up with some of these OG dudes such as yourself. Enjoyed the truck as mostly...143 replies | 11621 view(s)
